Oregon Scientific IWA-80055 - Manual (Page 2)

NOTE:
Attention! Please dispose of used unit or batteries in
an ecologically safe manner.
PLACING THE TRANSMITTER OUTSIDE
SPECIFICATIONS
MAIN UNIT
Recommended operating range: 0 °C to 45 °C
32 °F to 113 °F
Resolution: 0.1°C (above -10°C )
1°C (below -10°C)
0.1°F (-9.9°F ~ 99.9°F)
1°F (above 100°F & below -10°F)
REMOTE SENSOR
Recommended operating range: -20 °C to 55 °C
-4 °F to 131 °F
RF transmission frequency: 433 MHz
No. of remote unit: 1 unit
RF transmission range: maximum 100 feet
Temperature sensing cycle: around 60 ~ 64 seconds
Power
Main unit: 4.5V, use 3 x AA 1.5V alkaline battery
Remote sensor: 3 V, use 2 x AA 1.5V alkaline battery
Weight
Main unit: 8.57 oz
Remote sensor: 3.74 oz
Dimension
Main unit: 3.78(W) x 5.71(H) x 2.20(D) inch
Remote sensor: 1.57(W) x 1.26(H) x 0.94(D) inch
Transmitter’s low battery indicator
(shows on the main unit)
Remote Thermo Cloc
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
WARNING:
Changes or modifications to this unit not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio / TV
technician for help.
DECLARATION OF CONFORMITY
The following information is not to be used as contact
for support or sales. Please call our customer service
number (listed on our website at
www.oregonscientific.com or on the warranty card for
this product) for all inquiries instead.
We
Name: Oregon Scientific, Inc.
Address: 19861 SW 95th Place, Tualatin,
Oregon 97062 USA
DECLARE THAT THE PRODUCT
Product No.: IWA-80055
Product Name: Remote Thermo Clock
is in conformity with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference
received, including interference that may cause
undesired operation.
C 2008 Oregon Scientific. All rights reserved
IWA-80055
k
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn
more about Oregon Scientific products.
If you're in the US and would like to contact our
Customer Care department directly, please visit:
www2.oregonscientific.com/service/support.asp
OR
For international inquiries, please visit:
www2.oregonscientific.com/about/international.asp.
The transmitter should be located in an area protected
from direct sunlight and rain. Place the sensor under a
covered location like a roof overhand or under the eaves.
This will ensure accurate temperature readings. The
transmitter comes with a wall mounting/desktop holder.
When mounting on a wall, screw in place the holder
using the top and bottom holes. Then secure the transmitter
in the holder. The holder is also equipped with a table
stand. With the transmitter secured on the holder, retract
the leg on the rear of the holder and place on a flat surface.