Oricom M5000 - Manual (Page 8)

ABOUT YOUR PHONE
M5000 User guide.doc Page 15 of 20
10 Multi-handset use
Your M5000 series phone can have up to 5 handsets registered to 1 base unit. Each handset has its own
number HS-1, HS-2, HS-3, HS-4, & HS-5 shown on the left-hand side of the display. With 2 or more handsets
you can:
• Make intercom calls while on an outside call
• Switch between an out side call & intercom call
• Transfer an out side call from one handset to another
• Set a 3-way conference call between yourself, an outside call & intercom call
Make an intercom call
1. Press INTERCOM button. When you hear your outgoing message, press
2. Key the handset number 1, 2, 3, 4, OR 5 , you wish to call.
3. On the RECIEVING handset, press PHONE button.
4. To end, press PHONE button on the CALLING handset. The RECIEVING handset will hear a busy tone.
Transfer a call between handsets
1. Press INTERCOM button.
2. Key the handset number 1, 2, 3, 4, OR 5 , you wish to call.
3. On the RECIEVING handset, press PHONE button to receive call.
4. Press PHONE button on the CALLING handset to transfer. Call will return back within 90 seconds if
unanswered.
Transfer a speakerphone call to a handset
1. Press HANDSET LOCATOR button on the base unit.
2. Press PHONE button on the handset to pick up call.
Switch between calls
An outside call + an intercom call in progress, you switch between the 2 calls:
1. Press
INTERCOM button to speak to outside call, while the intercom call is on hold.
2. Press INTERCOM button again to speak to intercom call, while outside call is on hold.
3. Press PHONE to transfer outside call to the other handset (while connected to intercom call).
Notes
• A maximum of 1x outside call & 2x intercom calls can take place per base unit.
• If you make an outside call + another handset is on line = result is a busy tone.
• If you make an intercom call + one is already in progress = result is a busy tone.
Note
• If you press the PHONE button while connected to the outside call, you will
disconnect
• If the other handset user presses the PHONE button to hang up, you will be left with
the outside call
ABOUT YOUR PHONE
M5000 User guide.doc Page 16 of 20
Conference calls
A 3-way call between yourself + outside call + intercom call:
1. Either make or answer an outside call.
2. Press
INTERCOM button.
3 Key in the other handset number 1, 2, 3, 4, OR 5 .
4. On the RECIEVING handset, press PHONE button to receive call.
5. Press INTERCOM button & hold for about 3 seconds.
5. When connected both symbols are shown on display
11 Registering Handsets
Additional handsets
You may expand your M5000 by adding more handsets (M5050). These may be purchased separately from
the retailer where you purchased the product from, or direct from Oricom (Australia). The M5000 can
accommodate a total of 5 Handsets.
Register a handset
All handsets in Twin triple or Quad pack systems are already registered to your base unit. You won’t need to
register them unless you have a problem. Extra handsets purchased separately will need to be registered to
your base unit. Each handset can be registered with up to 4 base units.
Ensure no handset is resting on the base unit’s charging cradle:
1. Press & hold
HANDSETLOCATOR button on the BASE UNIT for 10s until the IN-USE light flashes (you have 3
minutes to register handset).
2. Key in a base unit number
1, 2, 3 OR 4, If you have one base unit key in 1.
3. Key in your handset’s PIN code default 0000 .
4. Handset now registered. You will hear a tone + display shows a handset number.
De-Register all handsets
To reset the system or to rearrange handset numbers you will to do the following:
1. Disconnect the mains power lead from the base unit & wait a few moments.
2. Reconnect the mains power lead.
3. Press & hold
HANDSETLOCATOR button until you hear a confirmation button.
4. Register all handsets as shown above.
Pause Insertion (for use with PBX)
When storing numbers in memory, you can include the out side line access digit (eg ‘9’ or ‘0’) with each
phone number. When using your phone on a PBX you may find the Last number redial or memory dial
don’t work. Try inserting a pause between the OUTSIDE LINE DIGIT & the TELEPHONE NUMBER.
1. Press the OUTSIDE LINE DIGIT eg ‘9’ or ‘0’
2. Press
LASTNUMBERREDIAL/P button to insert pause.
3. Press the keys for the rest of the TELEPHONE NUMBER