Outlaw Audio SEVEN-CHANNEL POWER AMPLIFIER VERSION 1.0 7125 - Manual (Page 2)

 Outlaw Audio
Owner’s Manual
Please Read First
Please Read First
CAUTION: To reduce the risk of electric shock, do not remove the cover (or back). No
user serviceable parts inside. Refer to qualified personnel.
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance
to rain or moisture.
The lightning flash with arrowhead, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous volt-
age” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating maintenance (servicing)
instructions in the literature accompanying the appliance.
Precautions
Verify The Line Voltage
Your new amplifier has been factory configured for 120 (+/- 3%) volt AC lines. Connect-
ing the amplifier to a line voltage other than that for which it is intended can create a
safety and fire hazard, and may damage the amplifier. If you have any questions about
the voltage requirements for your specific model, or about the line voltage in your area,
contact Outlaw Audio before plugging the unit into a wall outlet.
Verify AC Circuit Capacity
The high power output of your Outlaw amplifier may require heavy power draw under
full load conditions. To insure proper performance, and to avoid potential safety hazards,
we recommend that it be connected to a minimum 20 Amp capacity circuit. Connecting
multiple amplifiers to the same circuit, or connecting it to a circuit used by other heavy
power devices, such as air conditioners, may cause circuit breakers to trip.
NOTE: It is always a good idea to avoid using any audio or video equipment on the
same AC circuit as equipment with motors, such as air conditioners or refrigerators.
This will lessen the possibility of power variation and electrical start-up noise affect-
ing your sound system.
Extension Cords and Power Strips
We do not recommend that extension cords be used with this product unless they are of
sufficient gauge to pass the necessary current during full load conditions. Most inexpensive
extension cords are not capable of such high-current loads.
Similarly, should you use a power strip, surge protector or any type of AC power line con-
ditioning equipment, make certain that it is also able to handle the high current loads
this product will produce.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always pull the plug, never pull the
cord. If you do not intend to use the amplifier for any considerable length of time, discon-
nect the plug from the AC outlet. If the power cord is replaced, make certain that it is of
similar gauge. As with all electrical devices, do not run power cords under rugs or carpets
or place heavy objects on them. Damaged power cords should be replaced immediately
with cords meeting factory specifications.
Wiring
Cables that are run inside of walls should have the appropriate markings to indicate
complaince with, and listing by the UL , CSA or other standards required by the UL, CSA,
NEC or your local building. Questions about cables inside of walls should be referred to a
qualified customer installer, or a licensed electrician or low-voltage contractor.
Installation Location
To assure proper operation and to avoid the potential for safety hazards, place the unit on a
firm and level surface capable of supporting 100 pounds or more. When placing the amplifier
on a shelf, be certain that the shelf and any mounting hardware can support the weight of
the amplifier and any additional items in the equipment rack, or on the shelf.
When positioning the amplifier in its final location, make certain that it has adequate
ventilation on all sides, as well as on the top and bottom. In particular, it is a good idea
to provide at least two or three inches of room above the amplifier for air circulation. DO
NOT place CDs, DVDs, videotapes, owner’s manuals, or other paper on top of, or beneath,
the unit, or in-between multiple amplifiers in a stack. This will block airflow, causing heat
build-up, degraded performance, and may create a possible fire hazard.
If the unit is to be enclosed in a cabinet or rack, make certain there is adequate air cir-
culation. Sufficient ventilation should be provided so that hot air may exit, and cool air
may enter the cabinet. In some instances, a small cooling fan may be required to insure
adequate airflow through the cabinet. If you are in doubt as to the ventilation require-
ments for your specific installation, please contact us. Also, do not place the amplifier
directly on a carpeted surface, as this will inhibit airflow underneath as well as create a
potential fire hazard.
Avoid installation in humid locations, in extremely hot or cold locations, or in areas that
are exposed to direct sunlight or space heating equipment.
Loudspeaker Ratings
Your Outlaw Power Amplifier has adequate power to drive most loudspeakers without
producing any distortion. Most modern speakers are rated at four to eight ohms nominal
impedance, but within some frequency ranges, the impedance may drop to two ohms. The
Outlaw is designed with ample power reserves to protect you from experiencing any problems
at these low impeadances unless you demand excessively high volume levels.
Due to the high power output capability of your power amplifier, it is important that it not
be used with speakers not capable of handling the amplifier’s power output. Before using
the amplifier for the first time, make certain that your speakers are capable of handling
its rated power output, at the impedance rating of your speakers. Outlaw Audio is not
responsible for damage to any speaker system or other component that is caused by using
products whose power rating is lower than that of the amplifier.
Do Not Open The Cabinet
There are no user serviceable components inside this product. Opening the cabinet may
present a shock hazard, and any modification to the product will void your guarantee. If
water or any metal object, such as a paper clip, coin or a staple, accidentally falls inside
the unit, disconnect it from the AC power source immediately, and contact Outlaw Audio
for further instructions.
IMPORTANT SAFETY NOTE
Before connecting a new component such as power amplifier to your audio or home theater
system it is always good practice to make certain that all components are turned off, and
preferably unplugged from their AC power source. Many modern electronics products
feature automatic turn-on circuits that may be activated during an installation, causing
the potential for damage to electronic components and/or speakers. Such damage is not
covered by product warranties and Outlaw Audio specifically disclaims responsibility for
any such damage.
For Future Reference
Record your amplifier’s serial number and date of purchase here. It is found on the
back panel.
Model Number
Serial Number
Date of Purchase