Onkyo TX-NR1008 - Manual (Page 28)

28
En
Note
• Always turn down the volume before connecting your head-
phones.
• While the headphones plug is inserted in the PHONES jack, the
Headphone indicator, speaker/channel indicator FL and FR
lights. (The Powered Zone 2/3 speakers are not turned off.)
• When you connect a pair of headphones, the listening mode is
set to Stereo, unless it’s already set to Stereo, Mono, Direct, or
Pure Audio.
• Only the Stereo, Direct, Pure Audio, and Mono listening modes
can be used with headphones.
You can use ACTIVITIES to execute a number of remote
control operations with a single button.
This button has the following two modes.
`
Easy Macro mode:
You can turn on and off the AV receiver, playback
components and TV.
` Normal Macro mode:
You can assign desired operations (
➔ 89, 91).
Note
• If you set any one of the ACTIVITIES to Normal Macro mode,
all the ACTIVITIES will be set to Normal Macro mode.
• To use ACTIVITIES, first assign the remote control codes of the
AV components you are using ( ➔ 86).
Starting Components Using ACTIVITIES
*1 Depending on the start-up time of the playback component,
the AV receiver may not be able to activate the playback com-
mand. In this case, press on the remote controller.
Turning Off the Components
*2 When the last-pressed ACTIVITIES is MY MUSIC, the TV
will not turn off.
Changing the Playback Components
Assigned to ACTIVITIES
You can change the playback components assigned to the
ACTIVITIES of Easy Macro mode using the following
procedure.
Restoring Default
Using Headphones
Connect a pair of stereo headphones with a stan-
dard plug (1/4 inch or 6.3 mm) to the
PHONES
jack.
Using ACTIVITIES to Start Easy Macros
Press MY MOVIE, MY TV, or MY MUSIC.
At purchase, ACTIVITIES are set to Easy Macro
mode as the default setting.
The default actions are described below.
MY MOVIE:
1. The TV turns on.
2. The playback component assigned to BD/DVD
of REMOTE MODE turns on.
3. The AV receiver turns on.
4. The input selector of the AV receiver is set to
BD/DVD.
5. Playback begins on the playback component
assigned to BD/DVD. *1
MY TV:
1. The TV turns on.
2. The playback component assigned to CBL/SAT
of REMOTE MODE turns on.
3. The AV receiver turns on.
4. The input selector of the AV receiver is set to
CBL/SAT.
MY MUSIC:
1. The playback component assigned to TV/CD of
REMOTE MODE turns on.
2. The AV receiver turns on.
3. The input selector of the AV receiver is set to
TV/CD.
4. Playback begins on playback component
assigned to TV/CD. *1
Note
• After pressing one of the ACTIVITIES, you cannot use
other ACTIVITIES until the assigned actions have been
completed.
• If you wish to use another of the ACTIVITIES after start-
ing, press ALL OFF and then press the desired ACTIVI-
TIES.
Press ALL OFF.
The playback component assigned to the last-
pressed ACTIVITIES, the AV receiver, and the TV
turn off.
*2
While holding down REMOTE MODE for the rel-
evant playback component, press and hold down
ACTIVITIES to which you wish to assign this com-
ponent for about 3 seconds.
ACTIVITIES will flash twice, indicating that the
change is complete.
Examples:
If you wished to use MY MOVIE to start the play-
back component assigned to VCR/DVR of
REMOTE MODE, you would press and hold down
MY MOVIE for about 3 seconds while pressing
down VCR/DVR of REMOTE MODE.
Tip
• This procedure can also be performed via onscreen menu
( ➔ 89).
1
While holding down HOME, press and hold down
ALL OFF until ALL OFF lights (about 3 seconds).
2
Release HOME and ALL OFF and press ALL OFF
again.
ALL OFF flashes twice.