Onkyo AV Receiver TX-NR509 - Manual (Page 42)

42
En
Note
• This function can be set only if the “Subwoofer” setting is set to
“Yes”, and the “Front” setting is set to “Large” (
➔
page 41).
■
Wireless SB (Surround Back)
`
Yes:
The audio is output from the speakers connected to
the wireless unit.
`
No:
The audio is not output from the speakers connected
to the wireless unit.
When the wireless unit is connected to the UNIVERSAL
PORT jack on the AV receiver, you can select if you wish
to output the audio of surround back channel from the
speakers connected to the wireless unit.
Note
• If the “Surround Back” setting is set to “None” (
➔
page 41),
this setting cannot be selected.
■ Wireless SW (Subwoofer)
`
Yes:
The audio is output from the subwoofer connected to
the wireless unit.
`
No:
The audio is not output from the subwoofer
connected to the wireless unit.
When the wireless unit is connected to the UNIVERSAL
PORT jack on the AV receiver, you can select if you wish
to output the audio from the subwoofer connected to the
wireless unit.
Note
• If the “Subwoofer” setting is set to “No” (
➔
page 41), this
setting cannot be selected.
Menu Sp Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer
intended.
■ Unit
`
feet:
Distances can be set in feet. Range: 1ft to 30ft in
1 foot steps.
`
meters:
Distances can be set in meters. Range: 0.3m to 9.0m
in 0.3 meter steps.
(The default setting varies from country to country.)
■
Left, Center, Right, Surround Right, Surr Back
Right, Surr Back Left, Surround Left,
Subwoofer
`
Specify the distance from each speaker to your
listening position.
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
– the “Audio TV Out” setting is set to “On” (
➔ page 48).
– “HDMI Ctrl (RIHD)” is set to “On” (
➔ page 48) and
you’re listening through your TV speakers.
• Speakers that you set to “No” or “None” in the “Sp Config
(Speaker Configuration)” (
➔
page 41) cannot be selected.
Menu Level Cal
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
■
Left, Center *1 , Right, Surround Right, Surr Back
Right, Surr Back Left, Surround Left
`
–12 dB to 0 dB to +12 dB in 1 dB steps.
■
Subwoofer *1
`
–15 dB to 0 dB to +12 dB in 1 dB steps.
Note
• These settings cannot be calibrated in either of the following
cases:
– a pair of headphones is connected.
– the “Audio TV Out” setting is set to “On” (
➔ page 48).
– “HDMI Ctrl (RIHD)” is set to “On” ( ➔ page 48) and
you’re listening through your TV speakers.
– the AV receiver is muted.
• Speakers that you set to “No” or “None” in “Sp Config (Speaker
Configuration)” ( ➔ page 41) cannot be selected.
*1 For the center speaker and subwoofer, the level settings made
by using Home menu are saved here as the default settings.
Tip
• If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
When an optional unit is connected to the
UNIVERSAL PORT jack on the AV receiver, the
speaker setting menu may appear on screen.
Sp Distance (Speaker Distance)
This setting is set automatically by Audyssey 2EQ ®
Room Correction and Speaker Setup (
➔
page 28).
Level Cal (Level Calibration)
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup (
➔
page 28).