5842_5844_multiportrouter_may07_final 1, Model specific features, Common features – Quick Eagle Networks 5844 User Manual

Page 4

Advertising

© 2007 Quick Eagle Networks. All rights reserved.
PDF07/07
The information presented herein may change without notice
and should be used for informational purposes only. 5840
Multiport Router, 5842 Multiport Router, 5844 Multiport Router,
and 4335 Access Router are trademarks of Quick Eagle
Networks.

5842/5844 T

2xT1 ANSI T1.403 ports, max. 4xT1
T1 (1.544 Mbps ± 50 bps)
100 ohm RJ-48C socket
B8ZS
ESF
0 db, -7.5 db, or -15 db LBO or DSX-1
DSX -1 to -26 db
T1 Network, internal, external T1 source

FCC Part 15, FCC Part 68, UL 1950
Third Edition, Industry Canada CS-03
VCCI Class 1 CAN/CSA C22.2 No. 950-95

T1 network, T1 payload, fractional T1 payload,
loop-up/loop-down commands

T1 set/reset codes, ESF FDL per
AT&T 54016 and ANSI T1.403 Annex B

1:1, 1:2, 1:4, 1:7, 3:24, QRW, all 0s,
all 1s, two user-programmable 24-bit
patterns bit error injection

Loss of signal, loss of frame, remote alarm
indication, alarm indication signal, CRC6, BPV,

OOF

Power/test, network line status, network
loopback, loopback acknowledge, IP address,
SW version level

Non-intrusive monitor send/receive selectable
per T1 line

0º - 50º C
-20º - 60º C
0 - 95% non-condensing
4.6 Km (15,000 ft)

Model

Network Interface

Ports

Line Rate

Connector Type

Line Code

Framing

Output Level

Input Level

System Timing

Regulatory

Diagnostics

Loopback Tests

Loopback Control

Test Patterns

Network Alarms

Front-panel Status VFD and tri-color LED

Bantom test jacks

Environmental

Operating Temperature

Storage Temperature

Relative Humidity

Maximum Altitude

Model Specific Features:

5842/5844 E

2xE1 G.703 ports, max. 4xE1
E1 (2.048 Mbps ± 50 bps)
120 ohm RJ-48C socket
HDB3
ITU-T G.704/CTR 12
ITU-T G.703/CTR 12
0 to 20 dB
E1 Network, internal, external E1 source

European harmonized standards 73/23 EEC,

91.31/EED, 89/336/EED, 93/68/EEC, and

91/263/EEC; UL 1950 3rd Ed.; CAN/CSA

C22.2 No. 950-95; Comision Federal de

Telecommunica-ciones; CISPR 22 Level B

(EN 55022)

E1 network, E1 payload, fractional E1
payload, loop-up/loop-down commands

E1 set/reset codes

1:1, 1:2, 1:4, 1:7, 3:24, QRW, all 0s, all 1s,
two user-programmable 24-bit patterns bit
error injection

Loss of signal, loss of frame, remote
alarm indication, alarm indication signal,
CRC4, CV, FE

Power/test, network line status,

network loopback, loopback acknow-

ledge, IP address, SW version level

Not applicable

0º - 50º C
-20º - 60º C
0 - 95% non-condensing
3.05 Km (10,000 ft)

WAN Protocols

Independent Frame Relay or PPP links
Multilink Frame Relay FRF.16.1
MLPPP (RFC1990)
MAC Learning Bridge (IEEE 802.1d) over
Frame Relay (RFC2427) or PPP
MPLS VLAN tag transparency and
bridging
VLAN 802.1q
Multiple multilink bundles and support of
MLPPP / MLFR bundle classes A,B & C

IP Based DiffServ QoS (Optional)

Standard-based DiffServ compliant
(RFCs: 2475, 2597, 2598)
Priority queues (WRR, CBQ),
Congestion control (WRED)
Six forwarding classes
(EF, AF1, AF2, AF3, AF4, BE)
Traffic metering
Multifield classifier (Src/Dest IP address,
protocols, and applications ports)

Frame Relay

UNI-U and UNI-N interfaces
1024 DLCIs
LMI: ANSI (Annex D), ITU (Annex A), and
FRF Rev 1.0

Routing Protocols

Static routing
RIP1, RIP2, OSPF, optional BGP-4 (I-BGP

and E-BGP)
IP Fast Forwarding
DHCP server, DHCP relay
IGMPv3, IGMP proxy, IGMP-PIM
VRRP, GRE

Security and Management

Classless IP addressing
NAT (1:1), NAPT (overloading, port

translation)
Stateful Packet Inspection designed for

ICSA compliance
Radius Authentication, Secure Shell (SSH)
Router Command Line Interface (CLI)
RFC-868 Time Sync and Local Time
Zone capability

Performance Monitoring

RMON-1: PPP and Frame Relay adapted
RMON-2: Protocol directory, network layer
host, protocol distribution, application layer
host, network layer matrix, application layer
matrix

Ethernet Interface

10/100 Base T
Connector: RJ-45 socket

Local Management

RS232C COMM Port (VT 100 emulation)
Connector: RJ-48C socket

Remote Management

Telnet (in-band and out-of-band via SLIP)
SNMPv3

Service Level Agreement Verification

Frame Relay SLA FRF.13 compliant:
Frame Delivery Ratio (FDR),
Data Delivery Ratio (DDR),
Frame Transfer Delay,
Service Availability

Physical

Dimensions: 1 RU, rack mountable
43.69 cm (17.2 in ) W, x 40.64 cm (16 in)
D, x 4.45 cm (1.75 in) H
Weight: 5.45 kg (12 lbs.)

Power Requirements

Voltage: 100 VAC to 240 VAC, 50-60 Hz
or -40 VDC to -72 VDC (both on the same
platform)
Consumption: 30W maximum