Toshiba DVD Video Recorder / Video Cassette Recorder D-VR610KU - Manual (Page 39)

39 EN 39 EN
Disc
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
3 Use [K / L] to enter the date, then
press [B].
Timer Programming
1/1
TUE JAN/01 10:00AM
Date Start End L1/L2
New Program Date
JAN/02
SP 2 : 00
Start
- - : - -
End
- - : - -
L1/L2
L1
REC To Mode
DVD SP
Daily
MON-SAT
JAN/01
JAN/31
MON-FRI
SAT
FRI
SUN
4 Use [K / L / { / B] or [the Number
buttons] to enter the start and end
time, then press [B].
1/1
New Program Date
SP 2 : 00
Start End
- - : - -
L1/L2
L1
REC To Mode
DVD SP
JAN/02 12 : 00AM
• You cannot make a program whose recording
time exceeds 12 hours.
5 Use [K / L] to select an appropriate
external input (L1/L2) to which your
external tuner is connected, then
press [B].
1/1
New Program Date
SP 1 : 00
Start End
L1/L2 REC To Mode
DVD SP
JAN/02 12 : 00AM 1 : 00AM
L1
6 Use [K / L] to select a recording media
(“DVD” or “VCR”), then press [B].
1/1
New Program Date
SP 1 : 00
Start End
L1/L2 REC To Mode
SP
JAN/02 12 : 00AM 1 : 00AM
L1 DVD
7 Use [K / L] to select a recording
mode.
1/1
New Program Date
SP 1 : 00
Start End
L1/L2 REC To Mode
JAN/02 12 : 00AM 1 : 00AM
L1 DVD SP
Refer to “Recording Mode” on page 33 for DVD
or “Recording” on page 99 for VCR.
• You can check the remaining recordable space
of the disc when you select the recording
mode.
Date
SP 1 : 00
Start End
L1/L2 REC To Mode
JAN/02 12 : 00AM 1 : 00AM
L1 DVD SP
Auto recording mode select...
When “Auto” is selected as a recording mode, the unit
calculates how much time is available on the disc and
determines the appropriate recording mode to
complete recording the program.
1/1
New Program Date
Auto 1 : 00
Start End
L1/L2 REC To Mode
JAN/02 12 : 00AM 1 : 00AM
L1 DVD Auto
• “Auto” is only available for one program in the timer
program list.
• The recording may be cut short, when the available
recording space of the disc is too limited.
8 Press [ENTER] when all items are
entered.
Your program setting will be stored.
• To set another program, repeat steps 2 to 7.
• To exit, press [TIMER PROG.] or [SETUP].
• When 2 or more programs are overlapped,
“Timer program overlapped” appears, and the
overlapped program will be displayed in blue.
To correct the timer program refer to
“Checking, canceling, or correcting the timer
programming information” on page 40.
9 Press [TIMER SET] to set a timer
programming.
will appear on the front panel display, while this
unit waits to make the recording.
CS DR CD
HDD
DVD
“VCR” will appear on the front panel display if VCR
timer recording have been set.
TIMER RECORDING
When pressing [L] at
the current date, the
date will change as
follows.
e.g.) January 1st
E9KGAUD_D-VR610KU_EN.indd 39 E9KGAUD_D-VR610KU_EN.indd 39 2007/12/18 17:10:13 2007/12/18 17:10:13