Texas Instruments Dual/Single Socket CardBus and UntraMedia Controller PCI7621 - Manual (Page 198)

8−18
8.21 Interrupt Event Register
The interrupt event set/clear register reflects the state of the various PCI7x21/PCI7x11 interrupt sources. The
interrupt bits are set to 1 by an asserting edge of the corresponding interrupt signal or by writing a 1 in the
corresponding bit in the set register. The only mechanism to clear a bit in this register is to write a 1 to the
corresponding bit in the clear register.
This register is fully compliant with the 1394 Open Host Controller Interface Specification, and the PCI7x21/PCI7x11
controller adds a vendor-specific interrupt function to bit 30. When the interrupt event register is read, the return value
is the bit-wise AND function of the interrupt event and interrupt mask registers. See Table 8−15 for a complete
description of the register contents.
Bit 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
Name Interrupt event
Type R RSC RSC R RSCU RSCU RSCU RSCU RSCU RSCU RSCU RSCU RSCU RSCU RSCU RSCU
Default 0 X 0 0 0 X X X X X X X X 0 X X
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Name Interrupt event
Type RSCU R R R R R RSCU RSCU RU RU RSCU RSCU RSCU RSCU RSCU RSCU
Default 0 0 0 0 0 0 X X X X X X X X X X
Register: Interrupt event
Offset: 80h set register
84h clear register [returns the content of the interrupt event register bit-wise ANDed with
the interrupt mask register when read]
Type: Read/Set/Clear/Update, Read/Set/Clear, Read/Update, Read-only
Default: XXXX 0XXXh
Table 8−15. Interrupt Event Register Description
BIT FIELD NAME TYPE DESCRIPTION
31−30 RSVD R Reserved. Bits 31 and 30 return 0 when read.
29 SoftInterrupt RSC Bit 29 is used by software to generate a PCI7x21/PCI7x11 interrupt for its own use.
28 RSVD R Reserved. Bit 28 returns 0 when read.
27 ack_tardy RSCU Bit 27 is set to 1 when bit 29 (AckTardyEnable) in the host controller control register at OHCI offset
50h/54h (see Section 8.16) is set to 1 and any of the following conditions occur:
a. Data is present in a receive FIFO that is to be delivered to the host.
b. The physical response unit is busy processing requests or sending responses.
c. The PCI7x21/PCI7x11 controller sent an ack_tardy acknowledgment.
26 phyRegRcvd RSCU The PCI7x21/PCI7x11 controller has received a PHY register data byte which can be read from bits
23−16 in the PHY layer control register at OHCI offset ECh (see Section 8.33).
25 cycleTooLong RSCU If bit 21 (cycleMaster) in the link control register at OHCI offset E0h/E4h (see Section 8.31) is set to
1, then this indicates that over 125
µ s has elapsed between the start of sending a cycle start packet
and the end of a subaction gap. Bit 21 (cycleMaster) in the link control register is cleared by this event.
24 unrecoverableError RSCU This event occurs when the PCI7x21/PCI7x11 controller encounters any error that forces it to stop
operations on any or all of its subunits, for example, when a DMA context sets its dead bit to 1. While
bit 24 is set to 1, all normal interrupts for the context(s) that caused this interrupt are blocked from
being set to 1.
23 cycleInconsistent RSCU A cycle start was received that had values for the cycleSeconds and cycleCount fields that are
different from the values in bits 31−25 (cycleSeconds field) and bits 24−12 (cycleCount field) in the
isochronous cycle timer register at OHCI offset F0h (see Section 8.34).