Universal Electronics URC 7800 - Manual (Page 16)

31 30
Web Site : http://www.oneforall.com Web Site : http://www.oneforall.com
Red light does not
blink when you press
a key?
The Cinema 7+™
does not operate
your home entertain-
ment components or
is not performing
commands properly?
Problems program-
ming a TV/VCR
combo?
VCR not recording?
CH / and PREV
CH not working for
your RCA TV?
Problems changing
channels?
The red light blinks
when you press a
key but you receive
no response from
your home
entertainment
component?
Cinema 7+™ not
learning a command
from your original
remote control?
Tried “Search
Method” and still did
not find the code?
Sony’s Picture In
Picture (PIP) won’t
turn off?
Sharp’s Picture In
Picture (PIP) won’t
work properly?
Replace the batteries with four (4) new AAA alka-
line batteries.
Try all of the codes listed for your brand of home
entertainment component in the “Setup Codes” sec-
tion. Many setup codes may allow for partial func-
tionality, however, only one setup code will operate
your home entertainment component correctly.
Make sure that all of the components you are
setting up can be operated with an infrared
remote control.
Try the VCR set-up codes for your brand. However,
some combo units may require both a TV code for
volume control and a VCR code for the remaining
functions.
As a safety feature on the Cinema 7+™, you must
press the REC key twice.
Due to RCA design (1983-1987), only the original
remote control will operate these functions.
If your original remote control required an Enter
keystroke when changing channels, press the
ENTER key on the Cinema 7+™ after you enter the
channel number.
Make sure you are aiming your Cinema 7+™ at your
home entertainment component and that you are
within 15 feet before using your remote.
Make sure your remote controls are nose-to-nose
and are no more than 2 inches apart (see diagram
in step 5 on page 24).
Try the “Search Method” again after clearing out the
device key as follows: Press and hold SETUP until
red light blinks twice, then release. Next enter 9 - 9 -
2. Then press and release the device key to be
cleared twice.
Press TV once. Press and hold SETUP until red
light blinks twice, then release. Enter 9 - 9 - 4 and
press SETUP once. Then enter 6 - 2 - 1 and press
PIP On/Off. The red light should blink twice. PIP
should operate properly now.
Sharp’s PIP feature requires separate PIP functions
for “on” and “off”.
For PIP “on”, press TV once. Press and hold SETUP
until red light blinks twice, then release. Enter 9 - 9 - 4
and press SETUP once. Enter 3 - 4 - 8 and press PIP
On/Off. The red light should blink twice. PIP “on”
should operate properly now.
For PIP “off”, press TV once. Press and hold
SETUP until red light blinks twice, then release.
Enter 9 - 9 - 4 and press SETUP once. Enter 6 - 0 - 6
and press SETUP PIP On/Off. The red light should
blink twice. PIP “off” should operate by pressing
SETUP then the PIP key.
Problem Solution
TROUBLE SHOOTING
Press RCVR once. Press and hold SETUP until red
light blinks twice, then release. Enter 9 - 9 - 4 and
press SETUP once. Enter 3 - 9 - 8 and press SUR-
ROUND. Red light should blink twice. Surround
should operate now.
Try using the number pad on the Cinema 7+™ to
turn the receiver back on. For example, try pressing
0 to turn on in the CD mode, or 4 to turn on in the
Video 1 mode. Other numeric keys will also turn the
receiver on. If this doesn’t work, try the following:
Press RCVR once. Press and hold SETUP until red
light blinks twice, then release. Enter 9 - 9 - 4 and
press SETUP once. Then enter 5 - 9 - 1 and press
POWER. The red light should blink twice. Power
should operate properly now.
Audio functionality may be split between codes. For
example, Pioneer’s Tuner code 0014 works tuner
presets, but only Amplifier code 0013 works power
and volume. This also true for Sony’s Receiver code
0158 and Misc. Audio code 0159.
If some functionality is missing, try other codes to
see if functionality resides there.
These systems may operate using a CD or Misc.
Audio code. If the original remote control did not
have a power key, press PL (or STOP) to turn on
(or off) the system.
Surround on Sony
receiver will not
turn on?
Sony receiver will
turn off but not
back on?
Audio component
not fully-operational?
Mini-system, book-
shelf, or boombox
not working?
Problem Solution
TROUBLE SHOOTING (continued)
Consumer Help Line : 1-330-405-8606
E-Mail Address : [email protected]
World Wide Web : http://www.oneforall.com
▲
▲