Warning, Caution – Viking Refrigerator Drawer User Manual
Page 5
9
8
AREA REQUIREMENTS
Units Certified for Indoor Use - (black outer cabinet)
MUST BE INSTALLED IN AN AREA PROTECTED FROM THE ELEMENTS, SUCH AS WIND, RAIN, WATER (SPRAY OR
DRIP).
1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in
on the top and three sides, but the front M
MU
US
ST
T B
BE
E unobstructed for air circulation and proper operation.
Installation should be such that the cabinet can be moved for servicing if necessary.
2. Unit should be in a well ventilated area. Best results are obtained at temperatures between 55°F (12.8°C) and 80°F
(27°C) for built-in products and 55°F (12.8°C) and 90°F (32°C) for freestanding products.
3. Provisions for electricity and water connection should be determined before placing unit in proper place.
Units Certified for Outdoor Use - outdoor models contain a T after the base model number (ex. VURD144T) and
have a stainless steel outer cabinet.
MUST BE INSTALLED IN AN AREA PROTECTED FROM THE ELEMENTS, SUCH AS WIND, RAIN, WATER (SPRAY OR
DRIP).
1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in
on the top and three sides, but the front M
MU
US
ST
T B
BE
E unobstructed for air circulation and proper operation.
Installation should be such that the cabinet can be moved for servicing if necessary.
2. Unit should be in a well ventilated area with temperature above 40°F (4°C) and below 110°F (43°C).
3. Provisions for electricity should be determined before placing unit in proper place.
GENERAL INFORMATION
U
Un
np
pa
acckk
1. Remove banding from bottom of carton. Lift carton up and off of the unit.
2. Remove all tape and packaging material from the outside and inside of the cabinet.
3. Keep all carton packaging until your unit has been thoroughly inspected and found to be in good condition.
IIM
MP
PO
OR
RT
TA
AN
NT
T!!
Disconnect power source before adjusting leveling legs. A cabinet “anti-tip” device is mounted to the back of your
refrigerated drawer. If installation is a built-in undercounter application, you do not need to apply this feature. If your
installation is a free-standing application with no counter top directly above the top of the refrigerated drawer, you
must apply this feature to prevent the unit from tipping forward when the drawers are pulled out. the “anti-tip” device
is attached at the back of each cabinet. Please see installation instructions supplied with the “anti-tip” device.
WARNING
LEG LEVELER INSTALLATION
R
Re
ea
ad
d B
Be
effo
orre
e IIn
nsstta
alllliin
ng
g L
Le
eg
g L
Le
evve
elle
errss
1. Four leveling legs are pre-installed in the base of the unit at the factory.
2. The unit should be leveled from front to back and side to side. If floor
conditions do not allow the unit to sit level, adjust the leg levelers by turning
the required leg leveler counter-clockwise to increase the height and clockwise
to reduce the height.
WARNING
Do not lay unit on top, side, back, or front. If unit is accidentally laid in
any position other than right side up, then the unit must remain in the
upright position for at least 24 hours before plugging the unit in.
INSTALLING ANTI-TIP DEVICE
1. Push the unit against the wall so that the anti-tip bracket is flush to the wall adjacent to the back panel. Level
the unit with the leveling legs provided in the cabinet bottom. (See Leveling Legs on previous page.)
2. Using a pencil and the bracket as a template, trace the bracket on the wall, making sure two of the screw holes are
aligned with a stud in the wall.
3. Pull the unit away from the wall.
4. Remove the screws that connect the upper and lower sections of the anti-tip bracket.
5. Place the bracket on the wall and mark and drill 3/16” diameter Pilot holes for the provided 1/4” lag screws.
Mount the lower section ot the wall with the 1/4” lag screws.
6. Move the unit into place aligning the screw holes between the upper and lower brackets and secure with the
screws removed in Step 4.
A cabinet anti-tip device is mounted to the back of your refrigerated drawer unit. If your installation is a built-in
undercounter application with a countertop directly above the unit, this item can be removed. It does not need to be
applied.
If your unit is a free-standing application with no countertop directly above the top of the unit, you must apply this
feature to prevent the unit from tipping forward when the drawers are pulled out. The anti-tip device is installed on the
back of the unit. The anti-tip device reduces the chance of personal injury as well as property damage when properly
installed between the back of the unit and the adjacent wall. Please see the following instructions for installing the anti-
tip device.
CAUTION
FIGURE 4
Remove these screws to seperate
upper and lower sections of anti-tip
bracket.
To Refrigerated
Drawer Cabinet
To wall
1/4” Lag screws
into wall
FIGURE 3
Anti-Tip device