Viking Refrigerator Drawer - Manual (Page 7)

12
FULL OVERLAY PANEL INSTALLATION (con’t)
Step #3
S
Siizziin ng g tth he e O Ovve errlla ayy P Pa an ne ell
Step #4
A
Atttta acch hiin ng g tth he e O Ovve errlla ayy P Pa an ne ell tto o tth he e D Do oo orr
1. Set the overlay panel on drawer front face and align edges. Clamp panel in position and mark pilot hole locations.
See Step #3 for nominal size and hole locations. Drill pilot holes (remove panel if necessary, re-align and re-clamp
overlay to drawer face.)
2. Insert wood screws through clearance holes and tighten to secure overlay panel.
3. Reinstall gasket into channel. Make sure the corners are inserted fully.
Step #5
R
Re ea atttta acch h D Drra aw we err F Frro on ntt tto o D Drra aw we err B Bo od dyy
Align mounting holes on drawer body with mounting holes on drawer front. Align the door liner to the front flanges by
using the erasable marker alignment lines that were applied prior to removing the door from the drawer. Reinstall
phillips head screws and washers. Snug down, but do not tighten fully, final adjustment of drawer front will be done
after reinstalling the drawer.
Step #6
R
Re eiin nsstta allll tth he e D Drra aw we err
1. Fully extend drawer slides and place drawer on slides. Be sure that drawer sits evenly on both sides.
2. Lock drawers into drawer slides. Push drawer locks down and then back to relock the drawer into the slide.
Step #7
A
Ad djju usstt D Drra aw we err F Frro on ntt
1. Adjust drawer front to achieve a 1/8” gap from the top of the drawer front to the top of the cabinet or (for bottom
drawers) 1/8” from the top of the drawer front to the bottom of the top drawer, the drawer front should be centered
between the cabinet edges.
2. Fully tighten phillips head screws
23-5/8” (60.0 cm)
15-3/16”
(38.6 cm)
14-5/8”
(37.1 cm)
7-19/32”
(19.3 cm)
9/16”
(1.4 cm)
9/16” (1.4 cm)
11-13/16” (30.0 cm)
23-1/16” (58.6 cm)
13
FINAL PREPARATION
1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior of the unit should be
washed thoroughly with hot, soapy water, rinsed and wiped dry to remove film residue and any installation dust or debris
before being used. Solutions stronger than soap and water are rarely needed.
2. All stainless steel parts should be wiped with hot soapy water. If buildup occurs, do not use steel wool, abrasive cloths,
cleaners, or powders. If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to
loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape
stainless steel; scratches are almost impossible to remove.
ELECTRICAL CONNECTION
E Elle eccttrriicca all R Re eq qu uiirre em me en nttss
A 115 volt, 60 Hz, AC only 15 amp fused electrical supply is required. (A time delay
fuse or circuit breaker is recommended.) It is recommended that a separate circuit,
serving only this appliance, be provided.
• •E EL LE EC CT TR RIIC CA AL L G GR RO OU UN ND D IIS S R RE EQ QU UIIR RE ED D O ON N T TH HIIS S A AP PP PL LIIA AN NC CE E..
• •D DO O N NO OT T U UN ND DE ER R A AN NY Y C CIIR RC CU UM MS ST TA AN NC CE ES S R RE EM MO OV VE E T TH HE E P PO OW WE ER R S SU UP PP PL LY Y C CO OR RD D
G GR RO OU UN ND D P PL LU UG G..
• •D DO O N NO OT T U US SE E A AN N E EX XT TE EN NS SIIO ON N C CO OR RD D
R Re ecco om mm me en nd de ed d G Grro ou un nd diin ng g M Me etth ho od dss
For your personal safety, this unit must be grounded. This appliance is equipped with a 7’ (2.1 m) power supply cord having a 3-
prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong grounding type wall
receptacle grounded in accordance with the National Electrical Code and local codes and ordinances. If the circuit does not have
a grounding type receptacle, it is the responsibility and obligation of the customer to exchange the existing receptacle in
accordance with the National Electrical Code and applicable local codes and ordinances. The third ground plug SHOULD NOT,
under any circumstances, be cut or removed. All UL listed refrigerated drawers are equipped with this type of plug.
Power Supply
with 3-prong
grounding plug
Grounding type wall
receptacle
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result in fire or electrical
shock.
OPERATING INSTRUCTIONS
G Ge en ne erra all T Tiip pss a an nd d S Su ug gg ge essttiio on nss
•After making a temperature adjustment, allow at least 24 hours for your unit to reach a new temperature setting.
•The motor will start and stop often. It must do this to maintain the temperature setting.
•Unplug the unit before working on anything with the electrical system.
•Exercise caution when sweeping, vacuuming, or mopping near the front of the unit.
•Avoid leaning on the drawer fronts. You may bend the drawer slides or tip the unit.
WARNING