Document Outline

• PJD6221_UG_ENG.pdf
  • VPD-S5500-EN.pdf
    • FCC Notice
    • Safety Instructions
    • Notes on the AC Power Cord
      • Introduction
        • Projector Features
        • Package Contents
      • Projector with Lens Cap
      • AC Power Cord
      • VGA Cable (D-SUB to D-SUB)
        • Projector Overview
      • Using the Product
        • Control Panel
        • Connection Ports
        • Remote Control
        • Replacing the Battery
          • 1. Push the catch to the left and remove the battery holder.
          • 2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.
          • 3. Push the battery holder back into the remote control until you feel a click.
        • Remote Control Operation
      • Installation
        • Connecting the Projector
        • Powering On/Off the Projector
    • Powering On the Projector:
      • 1. Remove the projector lens cap.
      • 2. Complete the AC power cord and peripheral signal cable(s) connections.
      • 3. Press button to turn on the projector. The projector takes a minute or so to warm up.
      • 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
    • Powering Off the Projector:
      • 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
      • 2. Press button again to confirm.
      • 3. Disconnect the AC power cord from the electrical outlet and the projector.
      • 4. Do not turn on the projector right after power off.
      • Adjusting the Projector
    • Adjusting the Projector Height
      • 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.
      • 2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.
    • Adjusting the Projector Zoom and Focus
      • 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
      • 2. Adjust the image by sliding the zoom ring.
    • Adjusting Projection Image Size
      • Menu Operation
        • 1. Press the MENU button to open the OSD menu.
        • 2. When OSD is displayed, use p / q to select any feature in the main menu.
        • 3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.
        • 4. Use p / q to select the desired item and adjust the settings with t / u.
        • 5. Press the MENU button, the screen will return to the main menu.
        • 6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.
      • Maintenance
        • Cleaning the Lens
        • Cleaning the Projector Housing
        • Cleaning the Filter Cover
          • 1. Switch the projector off and unplug the AC power cord from the wall socket.
          • 2. Remove the filter cover as the illustration shown.
          • 3. Clean the filter cover.
          • 4. Replace the filter cover.
          • 5. Attach the filter cover.
          • 6. Plug the power back into the projector.
        • Replacing the Lamp
          • 1. Turn off the projector.
          • 2. If the projector is installed in a ceiling mount, remove it
          • 3. Unplug the power cord.
          • 4. Loosen the screw in the side of the lamp cover and remove the cover.
          • 5. Remove the screws from the lamp module, raise the handle, and lift out the module.
          • 6. Insert the new lamp module into the projector and tighten the screws.
          • 7. Replace the lamp cover and tighten the screw.
          • 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
          • 9. Reset the lamp hour. Refer to the “Setting” menu.
      • Specifications
      • Appendix
        • LED Indicator Messages
        • Compatibility Modes
    • Computer:
    • Video:
      • Troubleshooting
    • Start-up problems
    • Image problems
      • RS-232 Command and Configuration
      • IR Control Code
  • VPD-S5500-EN-0821.pdf
    • FCC Notice
    • Safety Instructions
    • Notes on the AC Power Cord
      • Introduction
        • Projector Features
        • Package Contents
      • Projector with Lens Cap
      • AC Power Cord
      • VGA Cable (D-SUB to D-SUB)
        • Projector Overview
      • Using the Product
        • Control Panel
        • Connection Ports
        • Remote Control
        • Replacing the Battery
          • 1. Push the catch to the left and remove the battery holder.
          • 2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.
          • 3. Push the battery holder back into the remote control until you feel a click.
        • Remote Control Operation
      • Installation
        • Connecting the Projector
        • Powering On/Off the Projector
    • Powering On the Projector:
      • 1. Remove the projector lens cap.
      • 2. Complete the AC power cord and peripheral signal cable(s) connections.
      • 3. Press button to turn on the projector. The projector takes a minute or so to warm up.
      • 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
    • Powering Off the Projector:
      • 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
      • 2. Press button again to confirm.
      • 3. Disconnect the AC power cord from the electrical outlet and the projector.
      • 4. Do not turn on the projector right after power off.
      • Adjusting the Projector
    • Adjusting the Projector Height
      • 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.
      • 2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.
    • Adjusting the Projector Zoom and Focus
      • 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
      • 2. Adjust the image by sliding the zoom ring.
    • Adjusting Projection Image Size
      • Menu Operation
        • 1. Press the MENU button to open the OSD menu.
        • 2. When OSD is displayed, use p / q to select any feature in the main menu.
        • 3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.
        • 4. Use p / q to select the desired item and adjust the settings with t / u.
        • 5. Press the MENU button, the screen will return to the main menu.
        • 6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.
      • Maintenance
        • Cleaning the Lens
        • Cleaning the Projector Housing
        • Cleaning the Filter Cover
          • 1. Switch the projector off and unplug the AC power cord from the wall socket.
          • 2. Remove the filter cover as the illustration shown.
          • 3. Clean the filter cover.
          • 4. Replace the filter cover.
          • 5. Attach the filter cover.
          • 6. Plug the power back into the projector.
        • Replacing the Lamp
          • 1. Turn off the projector.
          • 2. If the projector is installed in a ceiling mount, remove it
          • 3. Unplug the power cord.
          • 4. Loosen the screw in the side of the lamp cover and remove the cover.
          • 5. Remove the screws from the lamp module, raise the handle, and lift out the module.
          • 6. Insert the new lamp module into the projector and tighten the screws.
          • 7. Replace the lamp cover and tighten the screw.
          • 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
          • 9. Reset the lamp hour. Refer to the “Setting” menu.
      • Specifications
      • Appendix
        • LED Indicator Messages
        • Compatibility Modes
    • Computer:
    • Video:
      • Troubleshooting
    • Start-up problems
    • Image problems
      • RS-232 Command and Configuration
      • IR Control Code
  • PJD6221_UG_ENG.pdf
    • VPD-X5400-EN.pdf
      • FCC Notice
      • Safety Instructions
      • Notes on the AC Power Cord
        • Introduction
          • Projector Features
          • Package Contents
        • Projector with Lens Cap
        • AC Power Cord
        • VGA Cable (D-SUB to D-SUB)
          • Projector Overview
        • Using the Product
          • Control Panel
          • Connection Ports
          • Remote Control
          • Replacing the Battery
            • 1. Push the catch to the left and remove the battery holder.
            • 2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.
            • 3. Push the battery holder back into the remote control until you feel a click.
          • Remote Control Operation
        • Installation
          • Connecting the Projector
          • Powering On/Off the Projector
      • Powering On the Projector:
        • 1. Remove the projector lens cap.
        • 2. Complete the AC power cord and peripheral signal cable(s) connections.
        • 3. Press button to turn on the projector. The projector takes a minute or so to warm up.
        • 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
      • Powering Off the Projector:
        • 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
        • 2. Press button again to confirm.
        • 3. Disconnect the AC power cord from the electrical outlet and the projector.
        • 4. Do not turn on the projector right after power off.
        • Adjusting the Projector
      • Adjusting the Projector Height
        • 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.
        • 2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.
      • Adjusting the Projector Zoom and Focus
        • 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
        • 2. Adjust the image by sliding the zoom ring.
      • Adjusting Projection Image Size
        • Menu Operation
          • 1. Press the MENU button to open the OSD menu.
          • 2. When OSD is displayed, use p / q to select any feature in the main menu.
          • 3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.
          • 4. Use p / q to select the desired item and adjust the settings with t / u.
          • 5. Press the MENU button, the screen will return to the main menu.
          • 6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.
        • Network Control
          • 1. Connect one end of the internet cable to the Network Control connector on the projector.
          • 2. Connect the other end of the internet cable to an available RJ-45 connector on your computer.
          • 3. Turn on your projector and computer.
          • 1. Enable DHCP from the projector OSD, under Network Config.
          • 2. Start browser in PC and specify following URL, then click “Go” button.
          • 3. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.
          • 1. Set IP Address and Subnet Mask under Network Config.
          • 2. From your computer, go to Start > Settings > Network and Dial-up Connections > Local Area Connection and right click to select Properties..
          • 3. Select "Intel Protocol (TCP/IP)" and click "Properties".
          • 4. Set your PC’s IP address, and click OK.
          • 5. Start browser in PC and specify following URL, then click “Go” button.
          • 6. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.
          • 1. Go to Tools > General and click "Settings".
          • 2. Click "Every visit to the page" and "OK".
          • 3. Click "OK" to exit "Internet Properties".
        • Maintenance
          • Cleaning the Lens
          • Cleaning the Projector Housing
          • Cleaning the Filter Cover
            • 1. Switch the projector off and unplug the AC power cord from the wall socket.
            • 2. Remove the filter cover as the illustration shown.
            • 3. Clean the filter cover.
            • 4. Replace the filter cover.
            • 5. Attach the filter cover.
            • 6. Plug the power back into the projector.
          • Replacing the Lamp
            • 1. Turn off the projector.
            • 2. If the projector is installed in a ceiling mount, remove it
            • 3. Unplug the power cord.
            • 4. Loosen the screw in the side of the lamp cover and remove the cover.
            • 5. Remove the screws from the lamp module, raise the handle, and lift out the module.
            • 6. Insert the new lamp module into the projector and tighten the screws.
            • 7. Replace the lamp cover and tighten the screw.
            • 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
            • 9. Reset the lamp hour. Refer to the “Setting” menu.
        • Specifications
        • Appendix
          • LED Indicator Messages
          • Compatibility Modes
      • Computer:
      • Video:
        • Troubleshooting
      • Start-up problems
      • Image problems
        • RS-232 Command and Configuration
        • IR Control Code