Vestax PDX-d3S - Manual (Page 4)

3
19. R eplacement Parts-When replacement parts are required, be
sure the service technician has used replacement parts
specified by the manufacturer or have the same
characterristics as the original parts. Unauthorized
substitutions may result in fire, electric shock or other hazards.
20. Safety Check-Upon completion of any service or repairs to
product, ask the service technician to perfrom sefety checks
to determine that the product is in proper operating condition.
21. Carts and Stands-The appliance should be used only with
a cart stand that is recommended by manufacturer.
22. An appliance and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the appliance and cart combination to overturn.
F E A T U R E S NOTES
The PDX-d3S is a high end performance turntable designed
for the beginners and the professionals with the same basic
quality as the best selling turntable, the PDT-5000.
ANTI SKIPPING TONE-ARM SYSTEM,TRACING HOLD
BALANCE SYSTEM
New designed A.S.T.S(Anti Skipping Tone-arm System)
and TH(Tracing Hold) balance TONE-ARM system
protect skipping performance in hard scratching. And this
TONE-ARM provide adjustment mechanism of tone-arm
height which Vestax Turntable series have generally.
FAST STARTS BY HIGH TORQUE
Using high-torque direct motor, the integral motor delivers
1.6kg• cm start torque. The high-torque gives quick starts that
enables the platter to reach 33-1/3 rpm within 0.3 second.
FLOATING SUSPENSION TONEARM
The tone-arm is mounted on the deck plate using a floating
suspension system with the drive motor. Acoustic feedback
is minimized by this advanced system.
QUARTZ-PHASE-LOCKED CONTROL
The pitch is variable continuously by up to approximately
10%
and returned automatically to the predetermined speed (33-1/3 or
45 rpm) by on/off switch even if the pitch control is employed.
NON-CENTER-CLICK PITCH FADER
Pitch fader has no center click, and it allows delicate
adjustment easily. The PDX-d3S features detachable pitch
control fader for ease of replacement when it is worn out.
MINI LIGHT FOR ILLUMINATING STYLUS
The PDX-d3S provides detachable small stylus illuminator for
illuminating the stylus tip during play for low-light conditions.
OTHER FEATURES
Quick stops are achieved with an electronic braking
system. Remote control jack is provided for controlling
START/STOP by other equipment like a fader start etc.
Using FULL TIME QUARTS LOCK SYNTHESZER.
rotation of turntable is controlled. Using PLL circuit of the
two system. Accuracy of playing speed and time keeping
will be completed.
The pitch speed is controlled by none center click pitch
control fader volume. The pitch fader span can be selected
between ±12%, ±6%, ±3%.
MOTOR OFF function is provided to cancel servo brake
of the motor and REVERSE MODE will reverse the
turntable thus provided.
STICK CONTROLLER is provided for the functions of
pitch bend and FAST
SLOW, so that it is possible to
abjust speed up or down to begin phrase of a song without
touching the record.
Before detaching or attaching the headshell, be sure to turn
the power of the amplifier or mixer off.
Detaching or attaching of the headshell with the volume
control turned up may cause damage to the speakers.
Do not turn "ON" the power supply, with the turntable
platter detached.
When play is finished, be sure to secure the tone-arm with
the arm clamp. After play is finished, if the unit is not to
be used for some time, care should be taken to secure the
tone-arm to protect the stylus tip. For the same reason, the
stylus protector should also be attached.
Wipe the headshell terminals from time to time. Dust and
dirt at the headshell terminals may result in increased
"HUM" noise or intermittent sound. Use a soft dry cloth to
clean the heashell terminals.
Dust and dirt should be carefully removed from stylus tip
or records. Dust and dirt on the stylus tip or record may
not only result in deterioration of tone quality, but also
cause undue wear of the record and the stylus tip itself.
Transportation of the unit to distant places for removal and
the like. Pack up the unit in the reverse order to that for
unpacking, using the packing materials furnished when the
unit was purchased. Should there be no such packing
materials, be sure to take the following steps. Remove the
turntable platter together with the turntable mat, and wrap
it up to prevent any damage to them. Return the tone-arm
to the arm rest, and affix it with tape or the like. Remove
the balance weight and the headshell/cartridge from the
tone-arm and then wrap them up to avoid and damage to
them. Wrap up the turntable base with a blanket or soft
paper also to prevent any possible damage to it.
ACOUSTIC FEEDBACK AND HUM
Acoustic Feedback is usually cause by vibration of
speaker, which affects the sensitive cartridge. If such a
phenomenon occurs, relocate the turntable or speakers as
far apart from each other as possible. Hum is usually
cause by nearby appliances that use transformer or
thermostat. Relocating the unit further away from the
noise sources will readily solve the problem. Hum may
also be produced if the grounding wire extending from the
unit is securely connected to the GND terminal on the
amplifier of mixer.