Viking F20465A - Manual (Page 16)

31 30
S Se ea alle ed d S Su urrffa acce e B Bu urrn ne errss ((IIff a ap pp plliicca ab blle e))
Wipe up spill-overs as soon as possible after they occur and before
they get a chance to burn in and cook solid. In the event of a spill-
over, follow these steps:
1. Allow the burner and grate to cool to a safe temperature level.
2. Lift off the burner grates.
3. Remove the burner cap and clean per instructions below.
4. Wipe up any spills which remains on the sealed top surface.
5. Wash grates and burner caps in hot, soapy water and rinse clean.
6. Replace burner cop and grate after drying thoroughly.
If ports on the open or sealed burners are clogged, clean with a
straight pin. Do not enlarge or distort the ports. Do not use a
toothpick to clean the ports. When replacing burner caps, carefully
align the tabs underneath the cap with the outside edge of burner.
Make sure the tabs are not aligned with the igniter and the burner cap
is level.
S Se ea alle ed d B Bu urrn ne err A Allu um miin nu um m B Ba asse e ((IIff a ap pp plliicca ab blle e))
The aluminum base should be wiped regularly withhot soapy water at
the end of each cooling period. D
DO O N NO OT T use steel wool, abrasive
cloths, cleanser, or powders. To remove encrusted materials, soak the
area with a hot towel to loosen the material, then use a wooden nylon
spatula. D
DO O N NO OT T use a metal knife, spatula, or any other metal tool to
scrape the aluminum base. N NO OT TE E: For stubborn stains, use a non
abrasive cleanser such as Bon Ami TM and a soft brush or soft Scoth
Brite TM pad.
B Bu urrn ne err C Ca ap pss
The surface burner caps should be routinely removed and cleaned.
Always clean the burner caps after a spill over. Keeping the burner
caps clean will prevent improper ignition and uneven flames. To clean,
pull burner cap straight up from the burner base. Wipe off surface
burner caps with warm, soapy water and a soft cloth after each use.
Use a a non-abrasive cleanser such as Bon Ami and a soft brush or soft
scotch brite
TM pad for cooked-on foods. Dry thoroughly after cleaning.
For best cleaning and to avoid possible rusting, do not clean in
dishwasher or self-cleaning oven.
C Co on nttrro oll K Kn no ob bss
MAKE SURE THE CONTROL KNOBS POINT TO THE OFF POSITION
BEFORE REMOVING. Pull the knobs straight off. Wash in detergent
and warm water. Do not soak knobs. Dry completely and replace by
pushing firmly onto stem. DO NOT USE any cleaners containing
ammonia or abrasives. They could remove the graphics from the knob.
C Co on nttrro oll P Pa an ne ell
D DO O N NO OT T U US SE E a an nyy cclle ea an ne errss cco on ntta aiin niin ng g a am mm mo on niia a o orr a ab brra assiivve ess. They
could remove the graphics from the control panel. Use hot, soapy
water and a soft clean cloth.
W Wo okk C Ca asstt IIrro on n B Bu urrn ne err ((IIff a ap pp plliicca ab blle e))
For proper lighting and performance of the burner, keep the
electric igniter and burner ports clean. It is necessary to clean these only
when the flame does not burn blue completely around all rings of the
burner, when there is a severe spillover or when the burner does not
light, even though the electric spark igniter sparks. Clean the burner by
scraping off burned on food soil. Use a wire, a straightened paper clip,
or needle to clean the ports. D
Do o n no ott u usse e a a tto oo otth hp piicckk;; iitt cco ou ulld d b brre ea akk o offff
iin n tth he e p po orrtt.. B Be e ssu urre e tth he e vve en nttu urrii ttu ub be e rre em ma aiin nss d drryy..
Burner
ports
Venturi tube