Wibur Curtis Company PTTD-3 - Manual (Page 2)

PROGRAMMING ONLY REQUIRED IF FACTORY SETTINGS MUST BE CHANGED
Changing the ADS™ System Program
Your ADS System features a dynamic memory. In the event of a power loss it will remember ALL program settings.
IMPORTANT – Before entering the program mode, allow the unit to reach brewing temperature, then press the BREW
button to dispense at least 12 ounces of water. This is to clear any air that may be trapped within the water lines.
CONFIRM/RESET BREW TEMPERATURE - Factory Preset to 204º
ENTER THE PROGRAMMING MODE #1:
Press for two seconds, then RELEASE.
will start blinking. Each blink equals 2º F, starting at 170º (max. temp. 210º F or 21 blinks).
To change Temperature, press and HOLD .
.
will start QUICK flashing. Each QUICK flash equals 2º F.
After reaching 210º, temperature starts over at 170º.
RELEASE when the desired temperature is reached. The newly set temperature will now be displayed.
To set and exit, press .
For ALL functions you must first enter the programming mode.
Turn OFF the power from the Control Panel by pressing .
Press and HOLD and press and RELEASE .
Continue HOLDING until starts blinking; RELEASE.
ENTERING THE PROGRAM MODE #1
CHANGE BREW VOLUME - CONCENTRATE
ENTER THE PROGRAMMING MODE #1
Press and HOLD until hot water starts running from sprayhead; then RELEASE.
When desired volume is reached, press again to stop flow.
To set and exit, press .
CHANGE BREW VOLUME - DILUTION
ENTER THE PROGRAMMING MODE #1
Press and HOLD until cold water starts flowing from dilution faucet; then RELEASE.
When desired volume is reached, press again to stop flow.
To set and exit, press .
STEPS TO
PROGRAMMING
WARNING These steps
involve working with hot
water. Scalding may occur if
care is not taken against spilling.
Brew Temperature – Factory Pre-Set to 204°F
Function to set brew temperature, 170° to 210°F. Brew temperature will be indicated by READY-TO-BREW light blinking.
BREW VOLUME - Factory Preset to Brewer Requirements
CHANGING THE DRIP MODE (DWELL TIME) FEATURE
2
READY TO BREW
READY TO BREW
READY TO BREW
Illustrated Parts List - TCTD-35/35S Curtis Illustrated Parts List - TCTD-35/35S Curtis Illustrated Parts List - TCTD-35/35S Curtis Illustrated Parts List - TCTD-35/35S Curtis Illustrated Parts List - TCTD-35/35S Curtis
Iced Tea Brewer Iced Tea Brewer Iced Tea Brewer Iced Tea Brewer Iced Tea Brewer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
14A
15
16 WC-3322
WC-3647
WC-3320
WC-3201
WC-3358
WC- 750
WC-5450
WC-2977-01
WC-39260
WC-2965
WC-2906
WC-8556
WC- 895
WC-58017
WC-58021
WC-3502
WC-8531 BASKET, WIRE 6.4 DIA PTTD/TCTD USE W/WC-3320
STRAINER BT-10 BREWCONE (EXCEPT PARADISE)
BREW CONE W/HANDLE 8.8” D W/STRAINER
HANDLE, BREW CONE BLACK
BREWCONE ASSY, W/WC-3320, WC-3322 & WC-3647
CONTROL BOARD 120V 60Hz PTTD/TCTD
COVER, TOP BREWER
FITTING ASSY, SPRAYHEAD W/O-RING
MEMBRANE CONTROL PANEL, TCTD
SPOUT, BYPASS ASSY
SPRAYHEAD, BLUE .178 DIA ORF
HEAT SINK ASSY DV
VALVE, DUAL INLET 120V 10W
COVER, CENTER WRAP TCTD-35S
COVER, FRONT CENTER WRAP TCTD-35
LEG, 8-32 STD SCREW BUMPER
RAIL, BASE TCTD
DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION PART N PART N PART N PART N PART Nººººº ITEM ITEM ITEM ITEM ITEM
Continued – Page 3
TO ACCESS BREW CYCLE COUNTER
ENTER THE PROGRAMMING MODE #2:
will now start a pattern of LONG and SHORT blinks.
This pattern identifies the number of brew cycles. SHORT blinks indicate the brew number from one [1] to nine [9].
LONG blinks separate the 1’s, 10’s, 1,000’s and 10,000’s.
BREW CYCLE COUNTER
Note: Dwell time setting has an affect on
dilution water flow (even though the Drip
Mode starts at the end of brewcycle). Drip
modes set at 7 minutes or less results in
pulsing dilution flow. Drip modes set at 8 minutes or
more results in continuous flow of dilution water.
For ALL functions you must first enter the programming mode.
Turn OFF the power from the Control Panel by pressing .
Press and HOLD and press and RELEASE .
Continue HOLDING until STOPS blinking; RELEASE.
ENTER THE PROGRAM MODE #2
READY TO BREW
For ALL functions you must first enter the programming mode.
Turn OFF the power from the Control Panel by pressing .
Press and HOLD and press and RELEASE .
Continue HOLDING until STOPS blinking and remains on.
ENTER THE PROGRAM MODE #3
READY TO BREW
ENTER THE PROGRAMMING MODE #3
The will now blink a pattern of flashes from one
to ten. The first blink, if selected = 30 seconds; after that, each blink is one minute.
READY TO BREW
READY TO BREW