Wibur Curtis Company D500GT User Manual

D500 generation 3 - airpot brewer instructions, Ilbur, Urtis

Advertising

FFFFF

IND

OUT

MORE

THE

WEB

.....

W I L B U R

W I L B U R C U R

C U R

C U R T I S . C O M

T I S . C O M

Models Included

••••• D500GT
••••• D500GT/H

CAUTION:

CAUTION: DO NOT
connect this brewer to
hot water. The inlet valve

is not rated for hot water.

CAUTION:

CAUTION: Please use
this setup procedure
before attempting to use

this brewer. Failure to follow the
instructions can result in injury or
the voiding of the warranty.

ISO 9001 REGISTERED

WARNING HOT LIQUID,
Scalding may occur.
Avoid splashing.

Important Safeguards/Conventions

D500 Generation 3 - Airpot Brewer Instructions

FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO

WWW.WILBURCURTIS.COM

This appliance is designed for commercial use. Any servicing other than cleaning and maintenance
should be performed by an authorized Wilbur Curtis service center.

• Do NOT immerse the unit in water or any other liquid

• To reduce the risk of fire or electric shock, do NOT open top or rear panel. No user serviceable parts inside. Repair should

be done only by authorized service personnel.

• Keep hands and other items away from hot parts of unit during operation.

• Never clean with scouring powders, bleach or harsh implements.

Conventions

WARNINGS –

ARNINGS –

ARNINGS – TTTTTo help a

o help a

o help avoid personal injur

void personal injur

void personal injuryyyyy

Important Notes/Cautions – from the factory

Sanitation Requirements

YYYYYour Curtis

our Curtis

our Curtis ADS System is F

ADS System is F

ADS System is Factor

actor

actory Pre-Set and Read

y Pre-Set and Read

y Pre-Set and Ready to Go… Right out of the Carton.

y to Go… Right out of the Carton.

Following are the Factory Settings for your D500GT Airpot Coffee Brewing System:

• Brew

• Brew TTTTTempera

empera

emperature = 200°F

ture = 200°F

• Brew Volume = Set to dispensing vessel requirements (2.2 liters)

Generally there will never be a reason to change your ADS programming. However, should you need to make slight adjustments
to meet your brewing needs, programming instructions are provided later in this manual.

System Requirements:

•

• W

Waaaaater Source

ter Source

ter Source 20 – 90 PSI (Minimum Flow Rate of 1 GPM)

• Electrical:

• Electrical: See attached schematic for standard model or visit www.wilburcurtis.com for your model.

Equipment to be installed to comply with applicable federal, state, or local plumbing/electrical codes having jurisdiction.

SETUP STEPS

The unit should be level (left to right and front to back), located on a solid counter top. Connect a water line from the water filter to the
brewer. NOTE: Some type of water filtration device must be used to maintain a trouble-free operation. (In areas with extremely hard
water, we suggest that a sedimentary and taste & odor filter be installed.) This will prolong the life of your brewing system and
enhance coffee quality.

1. A 3/8” NPT x 1/4” Flare elbow has been supplied for water line connection. Use tubing sized sufficiently to provide a minimum of

1.0 GPM.

2. Connect the unit to an appropriate electrical power circuit.
3. Turn on the toggle (STANDBY/ON) switch behind the unit. The heating tank will start to fill. When the water level in the tank rises

to the correct volume, the heating elements will energize automatically. With ADS Systems there is no danger of element burnout
caused by an empty tank.

4. The heating tank will require 20 to 30 minutes to reach operating temperature (200°F) as indicated by the READY-TO-BREW

indicator light.

5. Prior to brewing, dispense 12 ounces of hot water through the hot water faucet.
6. Brew a cycle of at least 12 ounces, to purge the water lines of any air that may be trapped after filling.

The National Sanitation Foundation requires the following water connection:
1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be moved
for cleaning underneath.
2. In some areas an approved backflow prevention device may be required between the brewer and water supply.

BREWING INSTRUCTIONS

1. Brewer should be ON (Confirm at rear toggle switch, then press ON/OFF button). Ready-to-Brew should be displayed.
2. Place empty airpot on deck.
3. Place filter in brewcone.

4. Pour ground

coffee into

brewcone.

6.Press Brew

button.

ILBUR

URTIS

OMP

OMPANY

ANY

, I

.....

5. Position

brewcone

into brew

rails.

WILBUR CURTIS COMPANY

Montebello, CA 90640

CAUTION:

CAUTION: When
cleaning, DO NOT use
powders, liquids,

cleansers, or any substance
containing chlorine. These
products promote corrosion,
cause pitting of stainless steel and
will void the warranty.

Advertising

Popular Brands

Popular manuals