Whistler TOTAL BAND PROTECTION 425 - Manual (Page 4)

NOTE: Custom Mode automatically exits within 20
seconds if a button is not pressed. Messages are
kept in memory and are not affected by resetting
the factory features. See “Reset Features” section of
the manual.
To delete a message:
• Enter Custom mode and press Volume Up or
Volume Down button until selected band
appears on the display.
• Press the Quiet/Record button twice.
TIP: To prevent the recording of the stop button
press (click), allow the recording process to continue
for 15sec and automatically time out.
Power On and Self-Test
Each time your Whistler detector is turned on,
an automatic self-test sequence confirms that
the speaker and visual displays are functional.
• Press Power. Display shows in order:
1. WHISTLER 2. X-Band 3. K-Band 4. Ka-Band
5. Ku-Band 6
6.LASER 7. POP ON 8. VG2 OFF
9. SR OFF 10. Highway
• Display indicators will illuminate in the same order
on the XTR-325
Setting Saver
Setting Saver saves your personalized settings
so that when the detector is turned off and then
on again, you do not have to re-enter them.
Feature Engaged Confirmation
Each time a button is pressed, one beep confirms
feature “on”, two beeps confirm feature “off”.
Audio Level Adjustment
The audio levels can be adjusted high to low or
low to high.
• Press Volume up to increase audio level.
• Press Volume down to decrease audio level.
As audio level is adjusted, beeps are provided
and the display indicates volume level.
OPERATION
Auto Quiet Mode
Auto Quiet reduces the selected audio level to
level (1) approximately 5 seconds after a radar or
safety radar signal is detected. The alert for any
new signal within 20 seconds will resume at level
(1). Auto Quiet does not affect VG-2 or laser
alerts.
• Press Quiet/Menu (before a signal is detected)
to engage Auto Quiet.
• Once the Auto Quiet mode is engaged, you
may cancel the audio alarm by pressing Quiet.
• Press Quiet (when the unit is not alarming) to
cancel Auto Quiet mode.
Quiet Mode
Quiet cancels audio during an alert and any new
alert within 20 seconds. After 20 seconds,
approximately 2 beeps are provided on any new
alert and unit then remains quiet.
• Press Quiet to cancel the audio.
• Press Quiet a second time during an alert to
restore the standard audio alert pattern; or turn
the unit off, then on.
Teach/Tutorial Mode
Provides simulated alerts for each type of signal.
• Press City and Quiet simultaneously and
release.
• Display Shows: (XTR-425/560 only)
• Press Power to exit.
Highway Mode
Highway mode provides full audio warnings any
time radar (X, K, Ka, Ku, Safety Radar) or laser
signals are detected, and is recommended for
open road driving.
( Highway mode lets every signal in)
For more information on City and Highway mode, please
visit our FAQ page on our website:
www.whistler-
group.com
OPERATION
City/City 1/City 2 Mode
Whistler’s Three Stage City Mode is designed to
reduce the annoyance of automatic door open-
ers, intrusion alarms and other devices which share fre-
quencies with police radar. Generally, X band is
used for these devices.
• Press City to cancel Highway mode and
engage City.
• Press City again to enter City 1 Mode
- display shows ‘C1 Lo X’. (XTR 425/560)
• Press City again to enter City 2 Mode
- display shows ‘C2 No X’ (XTR 425/560)
• Pressing City a fourth time cancels City 2 Mode
and returns the unit to Highway Mode.
In City Mode, weak speed/safety radar signal
give an initial alarm of two beeps, and then
remains quiet unless the signal becomes very
strong. When the signal strength increases, two
additional beeps are provided. City 1 and City 2
Modes operate the same as Highway Mode, but
in City 1 Mode, only the X band sensitivity is low-
ered. In City 2 Mode, X-band is not detected.
Caution:
Some towns/small cities may still be
using X band radar. City Modes do not change
the audio alert for laser or VG-2.
Engaging/Disengaging VG-2
See Option Select Mode to turn this feature
on/off. When a VG-2 signal is detected, the VG-2
alert is sounded and the display flashes “VG-2”.
After 3 seconds the audio is canceled and the
display no longer flashes. This cycle is repeated
if the VG-2 signal is again detected. During the
period a VG-2 signal is detected, a radar signal
cannot be detected. However, because the VG-2
alert has confirmed that a patrol car is nearby,
you are already aware of the potential for speed
monitoring and can adjust your speed according-
ly. Laser detection is not affected while a VG-2
signal is detected.
OPERATION
8 9 10