Wayne-Dalton ALUMINUM FULL VIEW 452 - Manual (Page 4)

A
LUMINUM
F
ULL-
V
IEW 451 & 452
SECTIONAL DOOR SYSTEMS
Distributed By:
Printed in U.S.A.
Item #332549 Revised 9/2007
© 2007 Wayne-Dalton Corp. • One Door Drive • Mt. Hope, Ohio 44660 • 800-764-1457
Mt. Hope, OH • Dalton, OH • Trail, OH • Pensacola, FL • Portland, OR
For technical information, visit:
Specifications and technical information also available at www.arcat.com, SpecWizard™, and Sweets.com ® .
www. wayne-dalton .com/commercial
Note to specifiers: Words in parentheses indicate frequently specified and highly recommended options.
PART I – GENERAL
1.01 Section Includes
A. Sectional overhead doors [manually] [motor] operated
with accessories and components.
1.02 Related Work
A. Opening preparation,miscellaneous or structural steel
work,access panels finish or field painting are in the
scope of work of other trades and divisions of these
specifications.
1.03 Reference Standards
A. ANSI/DASMA 102 –American National
Standards Institute [A216.1] Specifications for sectional
overhead doors published by Door & Access Systems
ManufacturersAssociation International in bulletin
102-1990.
B. ASTM A123 – Zinc [hot-dipped galvanized]
coatings on iron and steel products.
C. ASTM A216 – Specifications for sectional overhead
type doors.
D. ASTM A229 – Steel wire,oil-tempered for
mechanical springs.
E. ASTM E330 – Structural performance of exterior
windows,curtain walls,and doors by uniform static air
pressure difference.
1.04 Quality Assurance
A. Sectional overhead doors and all accessories and
components required for complete and secure
installations shall be manufactured as a system from
one manufacturer.
1.05 Systems Description
A. Sectional Overhead Door:Type:
AFV 451/452
B. Mounting:Continuous angle mounting for [steel]
[wood] jambs [bracket mounting for wood jambs]
C. Operation:[manual push-up] [chain hoist] [motor]
[motor with chain hoist]
D. Material:AluminumAlloy 6063T6 [clear anodized]
[acrylic enamel]
1.06 Submittals
A. Shop Drawings:Clearly indicate the following:
1. Design and installation details to withstand
standard windload.
2. All details required for complete operation
and installation.
3. Hardware locations.
4. Type of metal and finish for door sections.
5. Finish for miscellaneous components and
accessories.
B. Product Data:Indicating manufacturer’s product
data,and installation instructions.
1.07 Delivery, Handling, Storage
A. Deliver products in manufacturer’s original containers,
dry,undamaged,seals and labels intact.
B. Store and protect products in accordance with
manufacturer’s recommendations.
1.08 Warranty
A. Provide manufacturer’s standard ONEYEAR warranty
against defects in workmanship and material.
PART I I – PRODUCTS
2.01 Manufacturer
A. Wayne-Dalton or approved equal AFV 451/452
overhead doors of aluminum alloy 6063-T6
construction complete as specified in this section and
as manufactured by Wayne-Dalton Corp.
2.02 Materials
A. Door Sections:Shall be of aluminum alloy 6063-T6,
1 3 /
8
" thick stiles and rails,joined with self tapping
screws
1. Rails –Top and bottom rails with 3 1 /
2
" wide,lower
intermediate rail 1 3 /
8
",upper rail 1 5 /
8
" ,minimum
wall thickness 0.062”.
2. Stiles –Top,bottom,and end stiles are 3 1 /
2
" wide,
center stile 3” wide,minimum wall thickness
0.062”.
3. Glazing – 1 /
8
" DSB (451) or 1 /
2
" double insulated
SSB (452)
B. Track:Track design shall be [standard lift] [high lift]
[vertical lift] [low headroom].Vertical mounting angles
shall be hot-dipped galvanized.Track size shall be [2"]
[3"].Vertical track shall be graduated to provide wedge
type weathertight closing with continuous angle
mounting for [steel] [wood] jambs,and shall be fully
adjustable to seal door at jambs [bracket mounting for
wood jambs].Horizontal track shall be reinforced with
continuous angle of adequate length and gauge to
minimize deflection.
Note: Horizontal track applies to standard lift,high lift,low
headroom and follow-the-roof designs only.
C. Hardware:Hinge and RollerAssembly:
1. Hinges and brackets shall be made from hot-
dipped,galvanized steel.
2. Track rollers shall be case-hardened inner
steel races with 10-ball [2"] [3"] rollers.
3. All factory authorized attachments shall be
made at locations indicated.
D. Counterbalance:
1. Springs shall be torsion type,low-stress,helical
wound,oil-tempered spring wire to provide
minimum [10,000 standard] [25,000] [50,000]
[100,000] cycles of use,on continuous steel [solid].
2. Spring fittings and drums made of die cast,high
strength aluminum.
3. Pre-formed galvanized steel aircraft cable shall
provide a minimum of a 5:1 safety factor.
2.03 Operation
A. Operation shall be [manual push-up] [chain hoist]
[motor] [motor with chain hoist].
Note: Manufacturer does not recommend chain hoists or
jack shaft operators on the following track applications.
• 15" radius standard lift with roof pitch
less than 2:12
• Hi-lift less than 24"
• Hi-lift between 12" – 23" with roof pitch
less than 1:12
• Low headroom track
Special chain hoist assemblies (using a trolley rail)
are available for the above track systems.
2.04 Locks
A. Locks shall engage the right-hand vertical track
and utilize [an interior side lock] [standard size
rim cylinder].
2.05 Weatherstripping
A. Doors shall be equipped with vinyl joint seals between
sections and vinyl“bulb” shaped astragal provided on
the bottom section.Optional top seal and jamb
seal are available.
2.06 Glazing
A. Optional.
2.07 Windload
A. Windload – per DASMA 102-2003 and as required by
local codes.
PART III – EXECUTION
3.01 Installation
A. General:
1. Install doors in accordance with manufacturer’s
instructions and standards.Installation shall be by an
authorizedWayne-Dalton representative.
2. Verify that existing conditions are ready to receive
sectional overhead door work.
3. Beginning of sectional overhead door work means
acceptance of existing conditions.
B. Install door complete with necessary hardware,jamb
and head mold strips,anchors,inserts,hangers,and
equipment supports in accordance with final shop
drawings,manufacturer’s instructions,and as specified
herein.
C. Fit,align and adjust sectional overhead door assemblies
level and plumb for smooth operation.
D. Upon completion of final installation,lubricate,test and
adjust doors to operate easily,free from warp,twist or
distortion and fitting for entire perimeter.
Note: Architect may consider providing a schedule when
more than one sectional overhead door or opening
type is required.
3.02 Materials (See note above.)