Winegard AS-2003 - Manual (Page 7)

7
2. After successful GPS acquisition,
the ON LED will come back on
and the SEARCH LED will
remain on, indicating the unit is
now moving in the search routine
and actively seeking the desired
satellites. When ON and SEARCH
LEDs are on at the same time,
Control Panel Operation
SEARCH/
MOVING
WINEGARD
ON OFF
PARK
AS-2003
SATELLITE SYSTEM
Unit is off. All four LEDs are off.
POWER ON
1. Press the ON button on the
control panel. All four LEDs will
flash and the ON LED will
remain on.
2. After approximately 5 seconds,
all four LEDs will flash while the
unit is checking for proper
signal level. If all four LEDs
remain on, refer to the WALL
PLATE ERROR CODES,
page 22.
3. After the signal is checked, the
ON LED and PARK LED will
remain on if the unit was last in
park position.
OR
The ON LED will remain on if
the unit was last in an upright
position.
SEARCH/
MOVING
WINEGARD
ON OFF
PARK
AS-2003
SATELLITE SYSTEM
SEARCH/
MOVING
WINEGARD
ON OFF
PARK
AS-2003
SATELLITE SYSTEM
SEARCH/
MOVING
WINEGARD
ON OFF
PARK
AS-2003
SATELLITE SYSTEM
SEARCH/
MOVING
WINEGARD
ON OFF
PARK
AS-2003
SATELLITE SYSTEM
SEARCH/
MOVING
WINEGARD
ON OFF
PARK
AS-2003
SATELLITE SYSTEM
SEARCH/
MOVING
WINEGARD
ON OFF
PARK
AS-2003
SATELLITE SYSTEM
SEARCH/
MOVING
WINEGARD
ON OFF
PARK
AS-2003
SATELLITE SYSTEM
SATELLITE SEARCH
1. Press the SEARCH button
one (1) time. The SEARCH
LED will come on and all other
LEDs will go off. This indicates
the unit is in search mode and
waiting for GPS acquisition.
GPS acquisition time will
range from immediate to several minutes. (Impor-
tant: Press the search button only once. Pressing
the SEARCH or PARK buttons in this mode will turn
the SEARCH LED off and the ON LED back on,
aborting the previous search. To restart, go to the
beginning of SATELLITE SEARCH procedure.
the unit is moving and searching. The search routine
can be stopped at any time by pressing the SEARCH
button or the PARK button; However, doing so will
return a SEARCH Error, turning the ON LED off and
the SEARCH and OFF LEDs on. The search can be
restarted by going to the beginning of SATELLITE
SEARCH procedure. The OFF button may also be
pressed to stop the search routine. The unit can be
restarted using SATELLITE SEARCH procedure.
SEARCH/
MOVING
WINEGARD
ON OFF
PARK
AS-2003
SATELLITE SYSTEM
3. When the unit is finished
searching and has stopped
moving, the SEARCH LED will
go off automatically, leaving
only the ON LED still on. This
indicates the unit has com-
pleted a successful search. It
will take approximately 4 to 5
minutes to complete a search routine after GPS ac-
quisition. If the unit has stopped and any other
LEDs (besides the ON LED) are on, refer to the
WALL PLATE ERROR CODES on page 22.
(NOTE: If an error message shows on the TV
screen during initial search, the signal has been
lost. This is normal and means the dish has tempo-
rarily lost the signal but is still searching (peaking).)
PARKING
1. If the unit is still powered on,
only the ON LED will be on.
Press the PARK button two
times (2) to park the unit. The
SEARCH and PARK LEDs will
also come on,indicating the unit
is moving to the park position.
(Important: If the unit has been turned off and on at
any time or the unit has been stopped using the
SEARCH or PARK button, it is only necessary to press
the PARK button one time (1), to park the unit.) Any-
time the ON, PARK and SEARCH LEDs are on at the
same time, the unit is moving to the park position. The
park routine may be stopped anytime by pressing the
SEARCH button or the PARK button. Pressing either
button will turn off the SEARCH and PARK LEDs, leav-
ing the ON LED still on. The park routine can be
restarted by pressing the PARK button one time (1).
The OFF button may also be used to stop
the park routine. The unit may be restarted going to
POWER ON procedure.
Step 3 continued on page 8.