Weider 8530 - Manual (Page 9)

9
During steps 13 to 25, refer to the CABLE DIA-
GRAM on page 19 of this manual. Identify the
three cables by their lengths, and note the
positions of the cable traps. IMPORTANT: Do
not overtighten the bolts and nuts securing
the pulleys. The pulleys must turn freely.
13. Locate the Medium Cable (58). Route the
Medium Cable around the indicated 3 1/2Ó
Pulley (15) attached to the Top Frame (55).
Be sure that the ball is on the indicated
side of the Pulley and that the Cable is
between the Pulley and the hook. Tighten
the 3/8Ó x 3 3/4Ó Bolt (88) and the 3/8Ó Nylon
Locknut (not shown).
14. Wrap the Medium Cable (58) around a ÒVÓ-
Pulley (50). Attach the ÒVÓ-Pulley and a Long
Cable Trap (31) to the indicated bracket on
the Front Upright (42) with a 3/8Ó x 2 1/2Ó Bolt
(86) and a 3/8Ó Nylon Locknut (21). Be sure
that the Long Cable Trap is positioned to
hold the Cable in place.
Route the Medium Cable (58) around the ÒVÓ-
Pulley (50) on the Left Arm (47). Be sure that
the Cable is in the groove of the Pulley and
that the Long Cable Trap (31) holds the
Cable in place. Tighten the 3/8Ó x 2 1/2Ó Bolt
(86) and the 3/8Ó Nylon Locknut (not shown).
15. Route the Medium Cable (58) around the ÒVÓ-
Pulley (50) on the Right Arm (48). Be sure
that the Cable is in the groove of the ÒVÓ-
Pulley and that the Long Cable Trap (31) is
positioned to hold the Cable in place.
Tighten the 3/8Ó x 2 1/2Ó Bolt (86) and the 3/8Ó
Nylon Locknut (not shown).
Route the Medium Cable (58) around the
3 1/2Ó Pulley (15) attached to the Pulley
Bracket (20). Be sure that the Cable is in
the groove of the Pulley and that the Cable
Trap (66) holds the Cable in place. Tighten
the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 2Ó
Bolt (not shown). Tighten the 5/16" x 5Ó Bolt
(68) and the 5/16" Nylon Locknut (not shown).
Be sure that the Pulley Bracket swivels freely.
16. See the inset drawing. Attach a 3 1/2Ó Pulley
(15) and a Cable Trap (66) to the upper hole
in the Long ÒUÓ-Bracket (57) with a 3/8Ó x 2Ó
Bolt (12) and a 3/8Ó Nylon Locknut (21). Be
sure that the Cable Trap is inside the Long
ÒUÓ-Bracket. (Note: This may come pre-
assembled.)
Route the Medium Cable (58) through the
3 1/2Ó Pulley (15) and Long ÒUÓ-Bracket (57)
shown in the inset drawing. Be sure that the
Cable is in the groove of the Pulley and
that the Cable and Pulley move smoothly.
16
13
14
15
CABLE ASSEMBL
Y
58
15
88
55
Ball
86
86
50
50
31
31
42
Bracket
21
58
47
58
15
20
68
21
66
86
31
48
15
15
66
12
21
58
58
57
57
50
Hook