Yamaha RX-V1200 - Manual (Page 48)

44
REMOTE CONTROL FEATURES
4 Press the button for which you want to
program the new function.
“LEARN” is displayed.
5 Press and hold the button on the other
remote control that has the function you
want to program into this remote control
until “OK” appears in the display window.
Notes
• “NG” appears in the display window when programming has
not been done correctly. In this case, start over from step 4.
• This remote control can learn approximately 120 functions.
However depending on the signals learned, “FULL” may
appear in the display window much earlier than this number. In
this case, clear unnecessary programmed functions to make
further learning on the remote control.
6 Repeat steps 4 and 5 to program additional
functions.
7 Press LEARN again to exit from the learning
mode.
Notes
• Even if the batteries in the other remote control have enough
power to transmit signals for operation, they may not have
enough power to transmit signals to this remote control.
• When the remote controls are either too close together or too
far apart, you may not be able to program this remote control.
• Direct sunlight interferes with infrared rays.
• “ERROR” appears in the display window when pressing more
than one button at once.
Programming a New Remote
Control Function (Learn Feature)
If you want to program functions not included in the basic
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. The possible
programming area is the same as a component control
area, so the buttons are programmable independently for
each source component area.
Note
• This remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn
most of the other remote control’s functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
1 Press an input selector button or Å to select
a source component.
2 Place this remote control and the other
remote control 1 to 4 cm apart on a flat
surface so that their infrared transmitters are
aimed at each other.
3 Press LEARN by using a ballpoint pen or
similar object.
Do not press and hold LEARN longer than three
seconds. Otherwise this unit enters the manufacturer
code setting mode.
Note
• If you do not press any button within 30 seconds during steps 5
and 6, the learning process is canceled. If this happens, start
over from step 4.
PHONO
POWER
SLEEP
CLEAR
LEARN
ST ANDBY
TRANSMIT
RE –NAME
6CH INPUT
SYSTEM V -AUX A
D -TV/LD POWER REC DISC SKIP
AUDIO
VOL
POWER
AMP
AV
TV
VCR2/DVR
VCR 1
DVD SELECT
CBL/SA
T
MD/T
APE
CD-R
TUNER
CD + –
1 to 4 cm (approximately 1 inch)
PHONO
POWER
SLEEP
CLEAR
LEARN
ST ANDBY
TRANSMIT
RE –NAME
6CH INPUT
SYSTEM V -AUX A
D -TV/LD POWER
POWER
AMP
AV
TV
VCR2/DVR
VCR 1
DVD SELECT
CBL/SA
T
MD/T
A PE
CD-R
TUNER
C D
PHONO
POWER SLEEP STANDBY 6CH INPUT
SYSTEM
V-AUX
A
D-TV/LD VCR2/DVR VCR 1 DVD
CBL/SAT MD/TAPE CD-R
TUNER CD
LEARN
Flashes alternately
LEARN
PHONO
POWER
SLEEP
CLEAR
LEARN
ST ANDBY
TRANSMIT
RE –NAME
6CH INPUT
SYSTEM V -AUX A
D -TV/LD POWER
POWER
AMP
AV
TV
VCR2/DVR
VCR 1
DVD SELECT
CBL/SA
T
MD/T
APE
CD-R
TUNER
CD
0108V1200_42-51_EN(UA) 01.7.6, 9:29 AM 44