Recording to md, Basic recording, 1basic recording 1 – Yamaha GX-900 User Manual
Page 38: Turn on the power, Press md rec/pause . * the md rec, Indicator lights up, Lights up on the display
30
Recording to MD
The MD recorder allows you to make recordings from a wide
variety of program sources (both analog and digital).
When recording an analog source (such as an LP or tape),
the MD recorder converts the analog signals to 44.1 kHz
digital signal before recording them onto the MD.
When recording a digital source, the MD recorder converts
the digital signals to 44.1 kHz for recording onto the MD.
However, If you are recording a 44.1 kHz source signal
(such as a CD) there is no conversion. The MD recorder can
record 32, 44.1 and 48 kHz digital signals.
Note
Adjusting the VOLUME, BASS and TREBLE controls,
YMERSION, B. BOOST and MUSIC buttons have no effect on
the recorded sound. The recording level is automatically
adjusted.
3
2
5
3
DISC
1
DISC
2
DISC
3
DOWN
UP
VOLUME
STANDBY/ON
MINIDISC RECORDER
MD
TAPE
DIRECTION
YMERSION
B.BOOST
MUSIC
INPUT
INPUT
MIN
PRESET/ TUNING/ BAND
A/B/C/D/E
DISC CHANGE
OPEN / CLOSE
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
DOLBY NR
HOUR
RANDOM
REPEAT
TIME
DISPLAY
MODE
MD EDIT
DELETE
PAUSE/ENTER
MD
CHARACTER
SET
REC/PAUSE
TAPE
1
1
A B C
D E F
G H I
J K L
M N O
P Q R
S T U
V W X
Y Z
/
2
2
3
3
4
4
5
5
6
6
7
7
8
8
R. TIME
C
EDIT
D
+
I0
E
MODE
REPEAT
RANDOM
SPACE
TUNER
DISC SKIP
POWER
SLEEP
INPUT
VOLUME
9
0
PRESET
TIME
A
PROG
B
CD
/I
YMERSION
BASS BOOST
MUSIC
INPUT MODE
M–MARK
SCROLL
TAPE
MD
REC/PAUSE
ENTER
DELETE
REC/PAUSE
DIRECTION
MD EDIT
1
1
Basic recording
1
Turn on the power.
2
Insert an MD into the disc insertion slot in the direction of
the arrow printed on the MD.
3
Select the input source by pressing INPUT
or
.
* If necessary, locate the point on the source where you
want to start recording and suspend the play at the point.
4
Press MD REC/PAUSE.
* The MD REC (
4
) indicator lights up.
5
Select the proper input mode by pressing INPUT MODE.
●
When recording a CD source or the source
connected to the DIGITAL IN terminal on the rear of
the main unit.
Select the Digital Stereo mode so that “DIGITAL” (
7
)
lights up on the display.
●
When recording other sources
Select the Analog Stereo mode so that there is no
illumination on the input mode indicator (
7
).
●
For the Digital Mono or Analog Mono input mode, refer
to “Monaural recording” on page 31.
6
Start playing the program source to be recorded.
* If a CD is played, recording also begins automatically.
(CD Synchronized Recording)
7
Press
(or
on the remote control) to start recording.
* “TOC” (
9
) lights up.
When “TOC” is illuminated, this means that the TOC
information has not yet been written to the disc.
To suspend recording
Press MD REC/PAUSE.
Press
again to resume recording.
To stop recording
Press .
Recording to both tape and MD
You can record a source to a tape and MD at the same time by
pressing both TAPE and MD REC/PAUSE in step 4 (except
using the EDIT function).
7
7
4
4