Yamaha RX-V2700 - Manual (Page 95)

93
En
GRAPHIC USER INTERFACE (GUI) SCREEN
English
AD
V
ANCED
OPERA
T
ION
Use the “V-RESET” in “ADVANCED SETUP” to set the
parameters in “Manual Setup (Video)” (except “Short Message”
and “On Screen”) to the factory presets (see page 127).
■ Conversion (Video conversion)
Use this feature to activate or deactivate the video
conversion as well as the HDMI up-conversion of the
analog video signals input at the composite video, S-video
and component video jacks.
Choices: Off,
On
• Select “Off” to deactivate the video conversion as well
as the HDMI up-conversion of the analog video
signals.
• Select “On” to activate the video conversion as well as
the HDMI up-conversion of the analog video signals.
• This unit does not convert 480 line video signals and 576 line
video signals interchangeably.
• The analog component video signals with 480i (NTSC)/576i
(PAL) of resolution are converted to the S-video or composite
video signals and output at the S VIDEO MONITOR OUT and
VIDEO MONITOR OUT jacks.
• The converted video signals are only output at the MONITOR
OUT jacks. When recording a video source, you must make the
same type of video connections between each component.
• When composite video or S-video signals from a VCR are
converted to component video signals, the picture quality may
suffer depending on your VCR.
• Even when “Conversion” is set to “On”, HDMI digital signals
are not converted to analog video signals.
• If “Conversion” is set to “Off”, the “Component I/P” and
“HDMI Up-Scaling” features are deactivated.
• Set “Conversion” to “On” to display the short message display.
• Unconventional signals input at the composite video or S-video
jacks cannot be converted or may be output abnormally. In such
cases, set “Conversion” to “Off”.
• When non-standard video signals (such as video signals from a
game console) are input, this unit may not convert the signals
even if you “Conversion” to “On”.
• When the analog component video signals with 480p of
resolution are input at the COMPONENT VIDEO jacks and the
video monitor is connected to the VIDEO MONITOR OUT or
S VIDEO MONITOR OUT jack of this unit, the GUI screen is
not displayed on the video monitor.
■ Component I/P
(Component interlace/progressive
conversion)
Use this feature to activate or deactivate the analog
interlace/progressive conversion of the analog video
signals input at the composite video, S-video and
component video jacks so that the analog video signals
deinterlaced from 480i (NTSC)/576i (PAL) to 480p/576p
are output at the COMPONENT MONITOR OUT jacks.
Choices:
Off , On
• Select “On” to activate the analog interlace/progressive
up-conversion of the analog video signals.
• Select “Off” to deactivate the analog interlace/
progressive up-conversion of the analog video signals.
• This menu item is not available and hence not visible in the GUI
screen if “Conversion” is set to “Off”.
• If your video monitor does not support analog video signals
with 480p/576p of resolution, the GUI screen may not be
displayed on your video monitor when “Component I/P” is set
to “On”. Use “V-RESET” in “ADVANCED SETUP” to set the
“Component I/P” parameter to the factory preset setting (see
page 127).
■ HDMI Up-Scaling (HDMI up-scaling)
Use this feature to activate or deactivate the HDMI up-
conversion of the analog video signals input at the
composite video, S-video and component video jacks so
that the up-scaled analog video signals are output at the
HDMI OUT jack.
This unit up-scales the analog video signals as follows:
• 480i (NTSC)/576i (PAL)
→ 480p/576p, 1080i or
720p
• 480p/576p
→ 1080i or 720p
Choices: Through, 480p (or 576p ), 1080i, 720p
• Select “Through” not to up-scale any analog video
signals.
• Select “480p” (or “576p”), “1080i” or “720p” to up-
scale analog video signals to 480p or 576p, 1080i or
720p of resolution.
Note
Notes
Off
On Conversion
Component I/P
HDMI Up-Scaling
Notes
On
Off Component I/P
HDMI Up-Scaling
HDMI Aspect
Conversion
Through
1080i
720p
480p HDMI Up-Scaling
HDMI Aspect
Short Message
Component I/P
Conversion