Zanussi ZWD 1680 W - Manual (Page 7)

7
3 “Prewash” button
With this option the machine performs a prewash cycle
at 30°C max. The prewash cycle ends with a short spin
at 650 r.p.m. in programmes for Cottons and Synthetics,
and with emptying of the water for Delicates.
This option is not available with the wool programme.
For use when washing heavily soiled laundry.
4 “40° AA” button
This option can be selected for cottons lightly or
normally soiled with a temperature of 40°C or higher
and for synthetics lightly or normally soiled with a
temperature of 50°C or higher.
If you select 60°C together with option 40° AA on
cottons programmes, the machine will prolong the time
in the washing phase and the washing temperature will
be reduced: this will allow an AA class in energy
efficiency and washing performance to be achieved.
If you select 95°C, 60°C, 50°C or 40°C and press the
40° AA button, the washing temperature will be reduced
and the washing time will be prolonged.
Important !
If you select the programme “E60°” (cottons) the pilot
light corresponding to the 40°AA option light up
automatically.
5 “Super Rinse” button
Can be used with all programmes except the wool
programme. The machine performs 4 rinses instead of
3.
This option is recommended for people who are allergic
to detergents and in areas where the water is very soft.
6 “Auto Dry” button
This button allows you to choose the required degree of
drying for cottons and synthetics:
- Extra dry (only for cottons)
- Store dry (cottons and synthetics)
- Iron dry (only for cottons)
The drying time is automatically adjusted by the
machine: the laundry will be dried to the selected degree
of dryness.
7 “Drying Time” button
If you wish to carry out a timed programme instead of
an electronic programme push the button until the
drying time you want appears in the display according
to the fabrics (cotton or synthetics) you have to dry.
For COTTON you can select a drying time from 10
minutes to 130 minutes.
For SYNTHETICS you can select a time from 10
minutes to 100 minutes.
8 “Delay Start” button
This button makes it possible to delay the starting of the
programme by up to 24 hours. The delay you have
selected is shown on the display for about 3 seconds;
afterwards, the duration of the programme reappears.
You must select this option after you have set the
programme and before you press the “Start/Pause”
button.
The time value shown on the display will decrease by
one unit every hour.
You can change the delay time at any moment,
before you press the “Start/Pause” button.
If you have already pressed the “Start/Pause” button,
and you wish to change or cancel the delay time,
proceed as follows:
• set the machine to PAUSE by pressing the
“Start/Pause” button;
• press the “Delay Start” button until the display shows
the desired delay time or
• press the “Delay Start” button once, to erase the delay
time. The display will indicate “ 0 h”.
• press the “Start/Pause” button again.
Important!
The door will be locked throughout the delay time.
If you need to open the door, you must first set the
machine to PAUSE by pressing the “Start/Pause”
button. After you have closed the door, press the
“Start/Pause” button again.
9 “Start/Pause” button
This button has three functions:
• Start: after you have selected the desired programme
and options, press this button to start the machine. The
light above the button will stop flashing and remain lit.
If you have selected a delay start by means of button
8, the countdown will begin and will be shown on the
display.
• Pause: when you press this button again, the
programme in progress is interrupted. The light above
the button will start flashing. To restart the
programme, press the button again.