York LDO9688 - Manual (Page 65)

65 YORK INTERNATIONAL
FORM 102.20-RP1(1104)
FILTER GAGE KITS
PART
NUMBER QTY DESCRIPTION
386-01161-001 1 FILTER GAGE ASSEMBLY - SINGLE FILTER BANK KIT
1 Ea. Gage, Differential Pressure, Minihelic II, 0-3”W.C
* 4 Ft. Tubing, Fire Rated Black Plastic,1/4” O.D.,.040” Wall
** 1 Ea. Eyelets, Flat Flange, .187 O.D., .503 Lg., .312 Flange,
Brass
1 Ea. Push Retainer for Non-Threaded Shaft, 3/16”
4 ea. Clamp, Tube, 1/4” O.D., Aluminum
386-01161-001 1 FILTER GAGE ASSEMBLY - TOTAL FILTER BANK KIT
1 Ea. Gage, Differential Pressure, Minihelic II, 0-3”W.C
* 4 Ft. Tubing, Fire Rated Black Plastic,1/4” O.D.,.040” Wall
** 1 Ea. Eyelets, Flat Flange, .187O.D., .503 Lg., .312 Flange,
Brass
1 Ea. Push Retainer for Non-Threaded Shaft, 3/16”
4 ea. Clamp, Tube, 1/4” O.D., Aluminum
386-01161-002 1 FILTER GAGE ASSEMBLY - COMBINED FILTERS KIT
2 Ea. Gage, Differential Pressure, Minihelic II, 0-3”W.C
* 6 Ft. Tubing, Fire Rated Black Plastic,1/4” O.D.,.040” Wall
** 2 Ea. Eyelets, Flat Flange, .187 O.D., .503 Lg., .312 Flange,
Brass
2 Ea. Push Retainer for Non-Threaded Shaft, 3/16”
6 Ea. Clamp, Tube, 1/4” O.D., Aluminum
1 Ea. Tee, Brass, Barbed, 1/4”
086-23690-001 1 Plate, Liner Cover, Minihelic II, 18 Ga., Stainless Steel
w/ 386-01161-001
086-23690-001 2 Plate, Liner Cover, Minihelic II, 18 Ga., Stainless Steel
w/ 386-01161-002
FIG. 22 - FILTER GAUGE DIAGRAMS
SIDE VIEW BACK VIEW
FILTER
AIRFLOW
PREFILTER
FINAL FILTER
BACK VIEW
AIRFLOW
LO
HI
SINGLE / TOTAL FILTER GAGE ONLY
PRE AND FINAL FILTER GAGES
PREFILTER
SIDE VIEW
FILTER
FINAL
MINIHELIC II 0-3"W.C.
MINIHELIC II 0-3"W.C.
MINIHELIC II 0-3"W.C.
LINER COVER PLATE
LINER COVER PLATE
1/4" BRASS TEE
RETAINER
EYELET
EYELET
RETAINER
2-5/8" DIA. MOUNTING HOLE
2-5/8" DIA. MOUNTING HOLE
3/16" DIA HOLE
3/16" DIA HOLE
NOTE:
IF FILTER GAGE IS MOUNTED
ON THE DOWNSTREAM SIDE
OF THE FILTER RACK, THEN
THE LOW PRESSURE PORT IS
TO BE LEFT OPEN AND THE
HI PRESSURE PORT IS TO BE
TUBED THROUGH THE BULKHEAD
PRESSURE PORT OF THE FINAL
IS TO BE TEE'D IN WITH HIGH
THE PREFILTER GAGE IS TO BE
THE HIGH PRESSURE PORT OF
OF THE FILTER RACK, THEN
ON THE DOWNSTREAM SIDE
IF FILTER GAGES ARE MOUNTED
NOTE:
TUBED THROUGH THE BULKHEAD
FILTER GAGE. THE LOW PRESSURE
PORT OF THE FINAL FILTER GAGE
IS TO BE LEFT OPEN.
AND THE LOW PRESSURE PORT
PREFILTER
FRONT VIEW
POLYESTER GAGE LABEL
HIGH PRESSURE SIDE LOW PRESSURE SIDE
HIGH PRESSURE SIDE LOW PRESSURE SIDE
LO
HI
FIG. 23 - TYPICAL FILTER GAUGE
LDO9660
LDO9711
* 1/4" tubing may be ordered separately, P/N 025-11958-000
** Sensor Probes (.187 eyelets) may be ordered separately. P/N 025-39050-000.