Yamaha RX-SL100RDS User Manual
Page 19
17
English
BASIC SETUP
PRE
P
ARA
T
ION
6
Press
k
/
n
repeatedly to select Room Size,
then press ENTER.
Use k/n to select the size of the room you have
installed your speakers in, then press ENTER.
Roughly speaking, the room sizes are defined as
follows:
[U.S.A. and Canada models]
S (small)
16 x 13 ft, 200 sq. ft
(4.8 x 4.0 m, 20 m
2
)
M (medium)
20 x 16 ft, 300 sq. ft
(6.3 x 5.0 m, 30 m
2
)
L (large)
26 x 19 ft, 450 sq. ft
(7.9 x 5.8 m, 45 m
2
)
[Other models]
S (small)
3.6 x 2.8 m, 10 m
2
M (medium)
4.8 x 4.0 m, 20 m
2
L (large)
6.3 x 5.0 m, 30 m
2
7
Press
k
/
n
repeatedly to select Subwoofer
Set, then press ENTER.
Use k/n to select Yes or None, then press ENTER.
Yes
If you have a subwoofer in your system.
None
If you do not have a subwoofer in your system.
8
Press
k
/
n
repeatedly to select Speaker Num,
then press ENTER.
Use k/n to select the number of speakers connected
to the unit, then press ENTER. The choices vary as
follows:
9
After you have finished the settings, press
n
repeatedly to select Setting OK?, then press
ENTER.
Use k/n to select Set or Cancel, then press ENTER.
Set
To apply the changes and start the test
tone.
Cancel
To cancel the changes and return to
Speaker Set Up.
Use the test tone to check the speaker levels.
If you selected Set, the display changes to “CHECK:
Test Tone”, and the unit outputs a test tone from each
speaker in turn. When the test tone begins, the display
changes to “CHECK OK: YES”.
• The unit cycles the test tone around each of the speakers in turn
twice.
• The indicator of the speaker currently outputting the test tone
flashes on the front panel display.
10
Press
k
/
n
repeatedly to select Yes or No,
then press ENTER.
Yes
To return to Speaker Set Up.
No
To enter Speaker Level.
■
Speaker Level
Use this menu to compare and adjust the test tone output
from each speaker to the output from the left front (or left
surround) speaker so that the volume level for all speakers
is identical.
Press ENTER to enter the Speaker Level
adjustment menu, then press
k
/
n
to select a
speaker and adjust the balance using
l
/
h
.
The unit outputs the test tone from the selected speaker
and the left front (or left surround) speaker in turn. The
indicator of the speaker currently outputting the test tone
flashes on the front panel display.
Choices
Display
Speakers
2 spk
Front L/R
3 spk
Front L/R, Center
4 spk
Front L/R, Surround L/R
5 spk
Front L/R, Center, Surround L/R
6 spk
Front L/R, Center, Surround L/R,
Surround back
L
L
C
R
SL SB SR
L
L C R
SL SB SR
L
L
C
R
SL
SB
SR
L
L C R
SL SB
SB SR
L
L C R
SL SB SR
Notes
Front
Speaker Set Up
Center
Speaker Level
Sur L
Sur R
Sur Back
01EN.00_RX-SL100RDS.book Page 17 Thursday, November 27, 2003 12:42 PM