Festool CS 70 st accessories PRECISIO - Manual (Page 8)

8
1 Scope of delivery (Fig. 1)
1.1 Guide unit consisting of:
2 guide rods mounted on 2 supports with 2
legs
1.2 1 Open-end spanner size 17
1.3 1 Open-end spanner size 10
1.4 1 Allen key 5 mm
1.5 1 Adjusting bracket, front
1.6 4 Bolts M6x16
1.7 4 Washers Ø 6
1.8 4 Bolts M8 x 25
1.9 2 Fitting angle
1.10 4 Square nuts
1.11 1 Washer 4 mm thick
(this washer is only needed as a com-
pensating washer when extension tables
and sliding table are fi tted)
1.12 1 Adjusting bracket, rear
1.13 Complete table, consisting of: aluminium
profi le plate with fi tted roller supports with
guide rollers and scraper
1.14 Extra clamp for stop guide
2 Technical data
Dimensions:
Width:
500 mm
Length: 420 mm
Max. slide travel: 1,250 mm
Max. cutting length: 920 mm
3 Fitting the sliding table
The sliding table is mounted on the left of the
PRECISIO.
Proceed as follows:
• Attach one fi tting angle (1.9) each onto the front
and rear of the table frame of the PRECISIO
(Fig. 2). Insert a square nut (1.10) into the cor-
responding square hole beneath the saw table
for the fastening bolt lying towards the middle
of the table. Place bottom side of fi tting angle
(2.3) on the rib (2.4) on the table frame and screw
in place with bolt (2.5). The nut for the second
fastening bolt is stuck to a strip as an assembly
aid. First insert a nut from the front into the
lateral opening (2.1) and screw in bolt. Then
remove strip and insert second nut into the rear
opening and screw rear fi tting angle in place.
• Attach the front and rear adjusting brackets
(5.1) to the carrier (5.5) using 2 screws (5.4)
and washers (5.6) with the mounting lobes (5.3)
facing inwards (Fig. 5). Adjusting brackets and
support must lie against one another following
assembly, do not tighten bolts yet.
• Suspend entire guide unit (rods) by suspension
lugs in the notches in the fi tting angles (2.3/1.9)
(Fig. 3).
• Push the head of the carriage bolt (5.2) through
the slots (2.2) in the frame, push bolt down and
tighten slightly with handle (3.1).
• Check that the supports rest on the adjusting
bolts (3.3) at the front and rear.
• To prepare for insertion of the sliding table:
- Fully open clip at rotary knob (6.5).
- Locate scraper (6.6) in correct position (bottom
edge parallel to guide rod).
• Place sliding table on the inner guide rod from
the front at a steep angle (almost vertical) (Fig.
6) so that the guide rod is between the roller
(6.4) and ball bearing (6.3).
• Fully insert sliding table and tilt into working
position (onto second guide rod).
• The sliding table can be locked with the rotary
knob (6.5).
4 Adjusting the roller guide
4.1 Checking the guide play
The play between the guide rod and guide rollers
is usually adjusted in the works. Nevertheless, we
recommend that the guide play at both rollers be
checked as follows:
• Push on sliding table from above. When the
sliding table is moved the outer ring of the bot-
tom ball bearing also rotates if the guide play is
correctly adjusted.
4.2 Adjusting the guide play
• Loosen the locking nut (6.1) with the size 17
open-end spanner.
• Adjust the position of the bearing via the cam
plate (6.2) using a size 5 Allen key (1.4).
• Re-tighten nut (6.1) following correction of the
guide play.
5 Adjusting the table height
A correctly adjusted sliding table is approx. 1 mm
higher than the top of the base table.
5.1 Checking the table height
• Fit angle fence on sliding table.
• Move stop guide so that it projects by approx.
20 mm over the base table.
• Check the gap between the tabletop and stop
and determine the amount of correction.