Festool CTL 22 E SG - Manual (Page 15)

15
- A hose coupling (1.10) (487072) can be
plugged into the opening (1.7). The suc-
tion hose is connected to the tool from
above with the hose coupling. Alterna-
tively, a hose clip (452998) can be fi tted
for coiling the suction hose.
- The push handle (2.11) (452921; supplied
ready with CTL 44 and CTL 55) makes the
vacuum cleaner easier to move. Acces-
sories (e.g. vacuum accessories) can be
fi xed to the push handle batten (2.9).
- An air blast is obtained by inserting a suc-
tion hose in the blast opening (2.7).
5.1 Vacuuming dry materials
A fi lter bag must be used without
exception when evacuating noxious
substances!
Before using the vacuum cleaner to evacu-
ate dry substances, a fi lter bag must al-
ways be inserted in the container. Then the
evacuated material can be disposed of eas-
ily. The fi lter element becomes damp after
evacuating liquids. A damp fi lter element
suffers more wear and tear if it is used for
dry materials. Accordingly, the fi lter ele-
ment should be dried or replaced with a dry
one before dry operation.
5.2 Vacuuming
liquids
Do not evacuate combustible liquids!
If foam or liquid escapes, stop work
immediately and empty the dirt con-
tainer.
The fi lter bag has to be removed before
evacuating liquids. We recommend use of a
special wet fi lter. When the maximum fi lling
level is reached, a bag-full indicator (2.12)
automatically interrupts extraction.
6 After fi nishing work
- Switch off the cleaner and pull the Plug of
the mains lead out of the Plug socket.
- Wind up the mains lead (2.6).
- Empty dirt tank.
- Clean the vacuum cleaner inside and out-
side by suction and wiping.
- Deposit the appliance in a dry room, safe
from unauthorised use.
7 Maintenance and care
Always remove the power supply
plug from the socket before carrying
out any work on the machine.
All maintenance and repair work
which requires the motor casing to
be opened may only be carried out
by an authorised service centre.
A safety test is to be carried out at least once
a year by the manufacturer or an instructed
person, e.g. for possible damage to the fi l-
ter and leaks in the appliance, and to ensure
that the control devices are functioning.
If the user services the appliance, it must be
dismantled, cleaned and serviced, as far as
possible without any danger to the mainte-
nance staff and other persons. Appropriate
measures include decontamination before
dismantling, locally fi ltered forced ventila-
tion on the dismantling site, cleaning the
service area, and suitable personal safety
equipment.
8 Accessories, fi lter
The accessory and fi lter order number can
be found in your Festool catalogue or on the
Internet under “www.festool.com”.
9 Warranty
Our equipment is under warranty for at
least 12 months with regard to material or
production faults in accordance with na-
tional legislation. In the EU countries, the
warranty period is 24 months (an invoice
or delivery note is required as proof of
purchase). Damage resulting from, in par-
ticular, normal wear and tear, o-verloading,
improper handling, or caused by the user
or other damage caused by not following
the operating instructions, or any fault ac-
knowledged at the time of purchase, is not
covered by the warranty. Damage caused
by the use of non-original accessories and
consumable material (e.g. sanding pads)
is also excluded. Complaints will only be
acknowledged if the equipment has not
been dismantled before being sent back to
the suppliers or to an authorised Festool
customer support workshop. Store the
operating instructions, safety notes, spare
parts list and proof of purchase in a safe
place. In addition, the manufacturer‘s cur-
rent warranty conditions apply.
Note
We reserve the right to make changes to
the technical data contained in this infor-
mation as a result of ongoing research and
development work.