Fein ASzx-648-1 - Manual (Page 16)

16 en
For your safety.
Read all safety warnings and all instruc-
tions. Failure to follow the warnings
and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
hand-held drill for drilling in metal, wood, plastic and
ceramics in weather-protected environments using the
application tools and accessories recommended by FEIN.
This machine is also intended to be powered by a.c. gen-
erators with sufficient power output that correspond
with ISO 8528, design class G2. Compliance with this
Standard in particular is not given when the so-called dis-
tortion factor exceeds 10%. When in doubt, inform
yourself about the generator in use.
Special safety instructions.
Use auxiliary handles provided with the machine. Loss of
control can lead to injury.
Beware of any concealed electric cables, gas or water con-
duits; check the working area with a metal detector, for
example, before commencing work.
Hold power tool by insulated gripping surfaces, when per-
forming an operation where the cutting accessory may con-
tact hidden wiring or its own cord. Cutting accessory
contacting a “live” wire will make exposed metal parts of
the power tool ‘“live” and shock the operator.
Secure the workpiece firmly. A work piece that is gripped
tightly in a clamping device or vice, is more secure than if
held by hand.
Do not machine any material containing asbestos. Asbestos
is cancerogenic.
Hold the power tool firmly. High reaction torque can
briefly occur.
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection against
an electric shock will be ineffective. Adhesive labels are
recommended.
Do not use accessories which are not specifically designed
and recommended by the tool manufacturer. Just because
the accessory can be attached to your power tool, it does
not assure safe operation.
Clean the ventilation openings on the power tool at regular
intervals using non-metal tools. The blower of the motor
draws dust into the housing. An excessive accumulation
of metallic dust can cause an electrical hazard.
Before putting into operation, check the mains connection
and the mains plug for damage.
Recommendation: Always operate the power tool via a
residual current device (RCD) with a rated residual current
of 30 mA or less.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
Character Unit of measure,
international Unit of measure,
national Explanation
n
0
/min rpm No-load speed
n
1
/min rpm Speed, full load
V V Rated voltage
P
1
W W Power input
P
2
W W Output
f Hz Hz Frequency
M… mm mm Size of metric thread
L
wA
dB dB Sound power level
L
pA
dB dB Sound pressure level
L
pCpeak
dB dB Peak sound pressure level
K… Uncertainty
m/s
2
m/s
2
Vibration emission value (triax vector sum) deter-
mined according to EN 60745
h. D
m/s 2 m/s 2 Mean vibrational value for drilling in metal
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
Basic and derived units of measure from the inter-
national system of units SI.
WARNING
3 41 01 089 06 0.book Seite 16 Freitag, 25. Juni 2010 8:07 08