NAD T 977 - Manual (Page 7)

3 Speaker
· The T 977 is equipped with special high-current binding-post
speaker terminals. Connect the respective SPEAKER FRONT L, FRONT
R, CENTER, SURR R, SURR L, SURR-BL and SURR-BR channels to their
corresponding loudspeakers. Make sure the “+” (red) terminal and
“-” (black) terminal are connected to the corresponding “+” and “-”
terminals of the loudspeaker. Use extra care to ensure that no stray
wires or strands cross between posts or terminals at either end.
· Always use heavy duty (16 gauge; 1.5mm, or thicker) stranded
wire to connect loudspeakers to your NAD T 977. The high-current
binding post terminals can be used as a screw terminal for cables
terminating in spade or pin sockets or for cables with bare wire
ends.
· The T 977 is designed to produce optimum sound quality when
connected to speakers with impedances within its operating range.
Please make sure that all the speakers are rated 4 ohms minimum
per speaker.
NOTE
Use stranded wire of at least 16 gauge (AWG). Connections to the T 977
can be made with banana plugs (120V version only) or by using bare
wire or pins. Use the transverse hole through the post for bare-wire or
pin connections. By loosening the terminal’s plastic nut, make a clean,
neat connection and re-tighten carefully. To minimize the danger
of short-circuit, ensure that only 1/2-inch of exposed wire or pin is
employed when connecting.
4 ground terminal
· The T 977 is provided with a GROUND terminal on the rear panel.
This terminal is connected directly to the chassis of the T 977.
· Use this terminal to properly ground the T 977. A ground lead wire
(not supplied) or similar can be used to connect the T 977 to ground
via this ground terminal. After insertion, tighten the terminal to
secure the lead.
5 Soft clipping
· Enables NAD’s proprietary Soft Clipping circuitry on all channels. At
“ON” position, Soft Clipping gently limits the output of the T 977 to
minimize audible distortion should the amplifier be over-driven.
· Soft Clipping may simply be left ON at all times to reduce the
likelihood of audible distortion from excessive volume settings.
However, for critical listening and to preserve optimum dynamics,
you may wish to defeat it by setting this switch to “OFF” position.
· The SOFT CLIPPING indicator on the front panel will illuminate when
the amplifier is in Soft Clipping mode.
6 +12v trigger in
· The +12V Trigger input allows the T 977 to be switched remotely
from standby mode to ON and vice-versa by ancillary equipments
such as a preamplifier, AV processor, etc. The controlling device
must be equipped with a 12V trigger output to use this feature.
WARNING
The front panel Standby button is disabled as long as the male plug
of the mono cable (with or without +12V DC) is connected to T 977’s
+12V TRIGGER IN. Unplug the mono cable for the T 977 to be normally
switched ON (or back to standby mode) using the front panel STANDBY
button.
7 fuSe holder
· In the unlikely event a fuse needs to be replaced, unplug the mains
power cord from the wall. Then, remove all connections from the
amplifier. Use a flathead screw driver or similar to open the fuse
holder via the slot indicated. With the screw driver in place, push
and turn counterclockwise to open the fuse holder.
· Only replace the fuse with the same type, size, and specification.
IMPORTANT NOTICE
Do not use any substitute fuses of different types or with different ratings
or values. Failure to observe this precaution may cause damage to the
amplifier circuits and may create a fire hazard and/or defeat the safety
built into the amplifier and may void the warranty.
8 ac mainS input
· The T 977 comes supplied with a separate detachable mains power
cord. Before connecting the plug to the mains powers source,
connect firmly first the other end to T 977’s AC Mains input socket.
· Connect only to the prescribed AC outlet, i.e., 120V 60 Hz (for 120V
version models only) or 230V 50 Hz (for 230V version models only).
· Always disconnect the mains power plug from the mains power
source first, before disconnecting the cable from the T 977’s AC
Mains input socket
POWERDRIVE
The T 977 uses NAD’s proprietary PowerDrive™ amplifier technology for
all channels to preserve accurate, linear reproduction regardless of the
loudspeaker. This uniquely efficient power-supply topology provides the
real-world benefits of high dynamic power that remains uncompromised
by low-impedance speakers.
By adding a second high-voltage rail to our well regulated high-current
power supply, we get an “overdrive” that can nearly double the continuous
power on a short term dynamic power basis. PowerDrive offers greater
amplifier stability and low impedance drive capability, resulting in less
distortion when driving real speakers with real program material.
IDENTIFICATION OF CONTROLS
rear panel
7
ENGLISH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ
T977_eng_OM_v04.indd 7 17/04/2012 9:28am