Candy CDI 1010__1 - S - Manual (Page 57)

According to the degree of hardness of
your water, regulate the softener unit in the
following way:
IMPORTANT
The dishwasher must be ALWAYS off
before start this procedure.
1. Press the "ON/OFF" button.
2. Wait for the programme indicator lights
to start flashing.
3. WITHIN 2 MINUTES of switching the
machine on, hold down the
"PROGRAMME SELECTION" button
(PR.) for at least 10 seconds (an
intermittent acoustic signal will sound).
4. When the 3 indicator lights on the left
will come on and the acoustic signal will
stop, release the button.
5. The light indicating the water softener
setting level will come on and the alarm
will shortly sound once. To change the
setting, press the "PROGRAMME
SELECTION" button: each time the
button is pressed, one indicator light
will come on (for level 5 all the indicator
lights will come on).
6. When the required setting is reached,
wait for the alarm to sound to indicate
that the settings were saved (the
programme indicator lights will return to
flash).
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning
(STEP 1).
113
WATER SOFTENER UNIT
Depending on the source of the supply,
water contains varying amounts of limestone
and minerals which are deposited on the
dishes leaving whitish stains and marks.
The higher the level of these minerals
present in the water, the harder the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special regenerating salt, supplies
softened water for washing the dishes.
The degree of hardness of your water can
be obtained from your water supply
company.
Regulating the water softener
with electronic programmer
The softener unit can treat water with a
hardness of up to 90°fH (French grading)
or 50°dH (German grading) through six
different settings.
The table below lists different degrees of
water hardness with the corresponding
setting for the softener unit.
*The water softener unit is set in the
factory at level 3, as this is suitable for
the majority of users.
Level
°fH
(French)
°dH
(German)
NO
YES
YES
YES
YES
YES
Indicator
light 1
Indicator
light 1
Indicator
light 2
Indicator
light 3
Indicator
light 4
Indicator
lights 1,2,3,4
Water
hardness
W
ater
softener setting Use of
regenerating
salt
0
1
2
*3
4
5
0-5
6-15
16-30
31-45
46-60
61-90
0-3
4-9
10-16
17-25
26-33
34-50
1 2 3 4
“PROGRAMME SELECTION” button
“ON/OFF”
button
Indicator lights
112
Connecting the outlet hose
■ The outlet hose should disharge into a
standpipe, making sure that there are no
kinks (fig. 4).
■ The standpipe must be at least 40 cm
above floor level and it must have an
internal diameter of at least 4 cm.
■ It is advisable to fit an anti-odour air trap
(fig. 4X).
■ If necessary the outlet hose can be
extended up to 2,5 m, provided that it is
kept at a maximum height of 85 cm
above floor level. The extension pipe is
available from the After Sales Service
Centre.
■ The hose can be hooked over the side of
the sink, but it must not be immersed in
water, in order to prevent water from
being syphoned back to the machine
when this is in operation (fig. 4Y).
■ When installing the appliance under a
worktop the hose pipe clamp must be
attached to the wall in the highest possible
position under the worktop (fig. 4Z).
■ Check that there are no kinks in the inlet
and outlet hoses.
4
Opening the door
If the machine comes open while it is working,
an electrical safety device automatically
switches everything off.
IMPORTANT
For the machine to work properly,
the door should not be opened while
it is in operation.
Closing the door
Place the baskets in the machine.
Make sure that both the spray arms are
free to rotate and are not obstructed by
cutlery, crockery or pans. Close the door,
pressing on it to make sure it is firmly shut.