Candy CDI 1010__1 - S - Manual (Page 64)

127
Alarm mute for the PROGRAMME
END
The alarm for the programme end may
be muted as follows:
IMPORTANT
The dishwasher must be ALWAYS off
before start this procedure.
1. Press the "ON/OFF" button.
2. Wait for the programme indicator lights
to start flashing.
3. WITHIN 2 MINUTES of switching the
machine on, hold down the
"PROGRAMME SELECTION" button
for at least 30 seconds (an intermittent
acoustic signal will sound).
4. When the 2 indicator lights on the left
will come on (to indicate that the alarm
is on) and the acoustic signal will stop to
sound, release the button.
5. Press the "PROGRAMME SELECTION"
button again.
The first 2 indicator lights from the left
will go off, while the other 2 indicator
lights will come on to indicate that the
alarm has been deactivated.
6. Wait for the alarm to sound to indicate
that the settings were saved (the
programme indicator lights will return to
flash).
7. To turn the alarm on again, follow the
same procedure.
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning.
Fault signals
If malfunctions or faults occur when a
programme is running the indicator light
that corresponds to the selected cycle
(2 indicator lights for the "COLD RINSE"
programme) will flash rapidly and the alarm
sounds.
In this event, turn the dishwasher off by
pressing the "ON/OFF" button.
After checking to make sure the water
inlet hose tap is open, that the drain
hose is not bent and that the siphon or
filters are not clogged, set the selected
programme again.
If the anomaly persists, contact Customer
Service Department.
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically discharge any excess
water should a problem occur.
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.
126
PROGRAMME SELECTION
AND SPECIAL FUNCTIONS
(Use in conjunction with programme guide)
Programme settings
■ Open the door and place the dirty dishes
inside the appliance.
■ Press the "ON/OFF" button .
■ After pressing the "ON/OFF" button, the
programme indicator lights will flash.
■ Choose a programme by pressing the
"PROGRAMME SELECTION" button
(PR.).
The selected programme indicator light
will come on.
When the "COLD RINSE" programme is
selected, 2 indicator lights will come on.
■ Close the door (after an audible signal
has sounded, the programme will start
automatically).
Programme interruption
Opening the door when a programme is
running is not recommended especially
during the main wash and final hot rinse
phases. However, if the door is opened
while a programme is running (for example,
to add dishes) the machine stops
automatically.
Close the door,
without pressing any
buttons . The cycle will start from where it
left off.
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.
Changing a running programme
Proceed as follows to change or cancel a
running program:
■ Hold down the "PROGRAMME
SELECTION" button until the programme
indicator lights will start to flash.
■ The running programme will be cancelled.
■ At this point a new programme can be set.
WARNING!
Before starting a new programme,
you should check that there is still
detergent in the dispenser.
If necessary, top up the dispenser.
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
Programme end
A 5 seconds alarm will sound (if not muted)
3 times at 30 seconds intervals to signal
that the programme has ended.
The programme indicator lights will start to
flash.
Dishes can now be removed and the
dishwasher turned off by pressing the
"ON/OFF" button or dishes can be loaded
for new cycle.