Acclaim Lighting X-Power HP Pro - Manual (Page 5)

000
100
010
110
001
101
011
111
0%
100%
1 2 3 ON
FADE TIME
"0" = "OFF" position
"1" = "ON" position.
(Dip Switches 10 = off)
1. The Stand Alone Mode enables;
2. Thus, flip the dip-switch 4,5 & 6(10-way Function Dip Switch)to adjust a desired level for chasing speed.
4 5 6 ON
SPEED
000
100
010
110
001
101
011
111
0.1S
0.2S
0.5S
1S
5S
10S
20S
30S
"0" = "OFF" position
"1" = "ON" position.
(Dip Switches 10 = off)
1. The Stand Alone Mode enables.
2. Thus, flip the dip-switch 1,2 & 3(10-way Function Dip Switch) to set a desired level for fade time.
-5-
5.2.1 Setting fade time
5.2.2 Adjusting chase speed
14%
28%
43%
57%
71%
86%
1. The Stand Alone mode enables;
2. Thus, flip the dip-switch 7,8 & 9 (10-way Function Dip Switch) TO select the desired program.
5.2.3 Selecting Built-in programs
000
100
010 1
2
3
7 8 9 ON
PROGRAM
(Dip Switches 10 = off) 110
001
101
011
111
4
5
6
7
AUTO
"0" = "OFF" position
"1" = "ON" position.
AUTO=a sequence of 7 programs
2.Main Features
3.Set Up
3.1 Power Supply:
Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your
power supply. The is available in a 120V and 230V version. Due to variations
in line voltage from venue to venue, be sure to plug your power supply into a wall outlet with matching
power before attempting to operate.
X-Power-HP-Pro X-Power-HP-Pro
Notice:
Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR
connector. Do not connect the cable's shield conductor to the ground lug or allow the shield conductor to
come in contact with the XLR's outer casing. Grounding the shield could cause a short circuit and erratic
behavior.
Figure 1
If you are constructing your own data cables, be sure to use standard two conductor
shielded cable (This cable may be purchased at almost all professional sound and
lighting stores). Your cables should be made with a 3-pin male and female XLR
connector on either end of the cable. Also remember that DMX lines must be daisy
chained and can not be split.
is a HP LED control unit, specially used to drive 1 Watt high power LED
fixtures, such as High Power LED Bar.
High frequency driving HP LED bars suitable for CCD cameras pick up facility.
is engaged as a combination of a control interface and tension provider
for 1Watt high power LED fixtures.
Ability of the maximum of 6 channels can be controlled separately, allows a maximum loads of 3x350mA
per output and the maximum amount connected loads distributed over all 6 outputs must not exceed 6A.
All work modes and parameters can be set by flipping 10-way Function Dip Switch and 6-way Mode Dip
Switch.
USITT DMX512(1990) multiplexed digital control, via 3 pin XLR connector or terminals.
DMX Control Mode and Stand Alone Mode available .
1~7 patterns plus a sequence of 7 patterns, chase speed & fade time adjustable..
Different Output Group modes for user assignable.
Output loading modes available in R.G.B mode, WHITE mode and COOL WHITE& WARM WHITE mode.
Manual Dim mode allows to control overall output intensity.
AC 110-120V/AC220-240V power input option by voltage selector.
Providing built-in DC24V 6.5A PSU.
Power Failure Memory.
X-Power-HP-Pro
X-Power-HP-Pro
Full range voltage of
-2-
3.2 Data Cable (DMX Cable) Requirements:
Connect the and your fixtures together using standard 3 pin DMX cables. The
uses DMX-512 protocol to operate your fixtures.
High Power DMX Controller TV
High Power DMX Controller TV
Figure 2
Figure 3
Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behavior. A terminator is a 120 ohm 1/4 watt resistor which is connected between pins 2 and 3
of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator will decrease the possibilities of
erratic behavior.
XLR Male Socket
1 Ground 2 Cold
3 Hot
XLR Female Socket
3 Hot
2 Cold 1 Ground
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
DMX 512 OUT
3-PIN XLR
1
2
3
1
2
3 DMX 512 IN
3-PIN XLR
Special Note: