Naxa NPB-255 - Manual (Page 3)

POWER SUPPLY
NOTE:
NOTE:
TO PLAY THE RADIO
q
q
BATTERY OPERATION
AC OPERATION
1. Remove the battery compartment cover gently.
2. Install 8 x 'C' size batteries (UM-2 or equivalent) while observing the correct polarities.
3. Replace the battery compartment cover.
The AC cord must be detached from the AC socket of the player.
Leaking batteries may damage the battery cabinet and the player as a whole, so
they should be removed from the cabinet when becoming flat or when the player is
not to be played on batteries for some time.
NOTE:
=
=
Insert the AC cord to the AC socket of the player, and plug the other end to an
applicable wall outlet.
Please be sure the AC Voltage Selector is switched to your local voltage if
applicable.
If the AC plug of this unit does not fit in with your AC outlet, a plug adaptor
should be used. Consult your local dealer on the type of plug adaptor.
1. Set the FUNCTION switch to the RADIO position, the POWER Indicator will light up.
2. Select the desired band with the BAND switch.
3. Tune to the desired station by rotating the TUNING control (rotate that control back and
forth until you get the strongest and clearest reception).
4. When FM (stereo) station is received, the FM indicator will be lit up.
5. The built-in AM antenna and external FM TELESCOPIC ANTENNA are directional.
When you are receiving an FM broadcast, fully extend the TELESCOPIC ANTENNA
and rotate it for the best reception.
For AM broadcast, rotate the whole set until the best reception is heard.
6. Adjust the volume level to a comfortable listening level.
7. To turn off the radio, set the FUNCTION switch to the OFF position.
=
=
5 4
LOCATION OF CONTROLS
1. FUNCTION SWITCH
2. VOLUME CONTROL
3. FM TELESCOPIC ANTENNA
4. FOLDING HANDLE
5. AUX IN JACK
6. CD DOOR
7. CD DOOR OPEN AREA
8. DIAL SCALE
9. BAND SWITCH
10. TUNING CONTROL
11. POWER INDICATOR
12. LCD DISPLAY
13. FM ST. INDICATOR
14. LEFT SPEAKER
15. SKIP/SEARCH DOWN BUTTON
16. SKIP/SEARCH UP BUTTON
17. 10+ BUTTON
18. USB PORT
19. PROG. BUTTON
20. MODE BUTTON
21. STOP/USB BUTTON
22. PLAY/PAUSE BUTTON
23. RIGHT SPEAKER
24. BATTERY COMPARTMENT
25. AC VOLTAGE SELECTOR
(ON THE BATTERY
COMPARTMENT) (OPTIONAL)
26. AC SOCKET
HANDLING AND MAINTENANCE OF A DISC
Follow the instructions below to handle and maintain your disc in order
that long time and trouble free performance can possibly be obtained:
=
=
=
=
=
Ensure not to caress the rain bow side of the disc; handle the disc
by the edge.
Long time exposure to sunshine, high temperatures and humidity
will damage the disc. And keep storage area clean.
Avoid sticking labels on both sides of a disc. Writing with pointed
articles on the disc should be strictly avoided.
Clean the disc wiping the centre and then working out to the edge
with a dry & soft cloth or a disc brush. Avoid any cleansing lotion or
chemical eradicator.
Store them in their cases when they are not to be used.
HANDLE DISC ONLY AS SHOWN
CLEAN FROM CENTER TO EDGE
DO NOT STORE NEAR HEAT
LOAD A DISC
PLAY A DISC
1. Open the CD door by the Door open area.
2. Load a disc on the disc tray with the label side facing up.
3. Close the CD door.
1. Slide the Function switch to CD/USB/AUX position.
2. Follow the steps above to load a disc.
3. The player begins readi
5. Press Play/Pause button once to halt music playback, the track number flashes to
indicate the player in Pause mode; press Stop button to cease music playback. The
LC
ng disc immediately.
4. When the disc is successfully read, total number of tracks shows in the LCD and
playback follows with the first track.
D shows the total number of tracks again.
and then a flickering track number shows on the screen
SKIP TRACKS AND SEARCH FOR A SPECIFIC POINT TO PLAY (CD)
PROGRAMMED PLAY (CD/USB/MP3)
1. Press once the SKIP/SEARCH up button in music play to skip to the next track. To skip
to a specific track ahead, press this button several times.
2. Press once the SKIP/SEARCH down button in music play to skip to the previous track.
To skip to a specific track at back, press this button several times.
3. Press 10+ button once in play to skip to the track 10 tracks ahead, twice to skip to the
track 20 tracks ahead. You can reach the last track of the disc using this button.
4. Hold the SKIP/SEARCH up button in music play to search at quick rate for a specific
point to play.
5. Hold the SKIP/SEARCH down button in music play to search at quick rate for a specific
point to play.
Programmed play is that tracks on the disc or on the USB can be edited for playback in a
preferred order with the use of PROGRAM button.
In stop mode, press PROG. button once, the program sequence indication "P01" flashes
with "PROG" icon in the LCD at the moment. Then a flickering track number shows in the
LCD with "PROG" icon waiting for your input, select the first track to be programmed using
SKIP/SEARCH buttons or 10+ button, and press PROGRAM button again to store and
advance to the next programming step. The program sequence indication changes to "P02"
waiting for your next input.