Naxa NDL-254 - Manual (Page 8)

7
RADIO OPERATION
1. Rotate the FUNCTION CONTROL to the RADIO position,
.
2. Select the desired band with the BAND switch.
5. Adjust the volume level to a comfortable listening level.
6. To turn off the radio, rotate the FUNCTION CONTROL to OFF
position.
the
POWER Indicator will light up
4. The built-in AM antenna and external FM TELESCOPIC
ANTENNA are directional.
NOTES:
TO PLAY THE RADIO
STEREO HEADPHONE JACK
AUXILIARY IN
—
—
—
—
When receiving an FM broadcast, fully extend the
TELESCOPIC ANTENNA and position for the best
reception.
For AM broadcasts, rotate the whole set until the best
reception is heard.
If a particular FM (STEREO) station is weak, or you hear
too much background noise, try moving the position of
the band selector switch to the FM(MONO) position.
This can often result in a much clearer reception.
When the band selector switch is set to FM STEREO
and a stereo broadcast is being received, the FM
STEREO indicator the unit will be light.
A stereo headphone jack has been provided on the top of the unit
so that you can listen to the unit without disturbing others. To use
this jack, plug in the headphones/earphones (not included) and
adjust the VOLUME control to a comfortable listening level.
NOTE: When external headphones/earphones are connected,
the sound to the unit's main speakers will be muted.
Your player can be used as a power amplifier to playback the
programs from portable radio, TV set or Mp3 player or
whatever provide this appliance is so designed that audio
signal may be produced through a LINE-OUT jack or the like.
Observe the following steps to connect the player to another
appliance:
1. Power the player on using the supplied AC Power Cord.
2. Rotate the FUNCTION CONTROL to AUX-IN position.
3. Connect the appliance into the player's AUX-IN jack with
supplied LINE-OUT cable of the appliance.
4. Power on the appliance and begin play.
At this time you will be able to hear the sound produced from
the programs the connected appliance is broadcasting.
MIC
The MIC jack works in disc, USB and card mode. If you want to
use the microphone for singing or speaking, please connect it
to MIC jack.
3. Tune to the desired station by rotating the TUNING control
(Move the control back and forth until you get the strongest
clearest sound).
TV OPERATIONS
GET STARTED
SEARCH A PROGRAM
—
—
—
—
—
—
Be sure the TV antenna is connected to the set properly.
Power on the unit. Rotate FUNCTION CONTROL to
TV/DVD position, and press TV/DVD button on the remote
or press and hold the MODE/TVMENU button on the unit to
switch to TV mode.
Note: It is recommendable to scan channels first for the first
time using or no channel broadcasts. Please follow the below
steps to scan channels:
1. Press TV MENU to enter the TV setup menu, then use
navigation buttons to select "AUTO SCAN" option.
2. Press NAVIGATION RIGHT button to access the submenu,
3. select the properly Cable system and enter the Start to Scan
option to begin auto scan for scanning channels. (
Press FAST REWIND button or FAST FORWARD button on
the unit or navigation up/down button on the remote once,
the channel number changes. A desired channel can be
reached using these two keys.
NUMERIC button on the remote ca n facilitate you to select
a specific channel. If the channel number exceeds 10, input
first digital unit, then another digital unit;
Note: this receiver can store the channels from 2~69, and
the maximum of each channel has 8 programs. To select the
desired programs by using - button and numeric buttons.
Do as follows:
To select CH 13 NO. 2
Press 1 and 3, then press +10 and input 2.
Once the input is done, it will start broadcasting the selected
channel immediately.
During TV playback, press MTS button to adjust the audio
output language.
Press DISPLAY button to display current program information
including current channel mode, resolution, current calender
and time, soundtrack mode.
The CC button is used to set the closed caption mode. Press
CC button repeatedly to set the CC mode (Off/On/CC on mute).
In TV play mode, press P MODE button on the remote several
times to select your desired picture mode (Personal, Standard,
Dynamic, Soft)
Use GUIDE button to check information of the program guide
for the past and future. The Information in the EPG depends on
your signal provider.
BASIC OPERATIONS
ADJUST AUDIO OUTPUT LANGUAGE
DISPLAY PROGRAM INFORMATION
SET CLOSED CAPTION
PICTURE MODE
ELECTRONIC PROGRAM GUIDE
MUTE
SOUND MODE
In TV mode, press MUTE button to shut off the audio output,
press it again resume normal play.
During TV broadcasting, press AUDIO button repeatedly to
switch sound mode among personal, standard, movie and
music.
Frequency
range: 57 - 855 MHz)