VTech CS6124_-2-31 Quick start - Manual

Quick start guide
CS6120-2/CS6124/CS6124-2/CS6124-31
Introduction
This quick start guide provides you with the basic installation
instructions. A limited set of features are described in
abbreviated form.
You may refer to the Abridged user’s manual provided in the
product package for installation and operation instructions, or see
the online Complete user’s manual at www.vtechphones.com for
complete installation and operation instructions.
Telephone base and charger installation
Install the telephone base and charger as shown below.
Use only the power adapters and batteries supplied with
this product.
If you subscribe to telephone service from a cable
company or a VoIP service provider, contact your cable/
VoIP service provider for more information.
•
•
Battery installation and charging
Install the battery as shown below. Once you have installed the
battery, you may be able to make and receive short calls. For best
performance, charge the handset battery continuously for at least
16 hours.
1 Plug the battery connector
securely into the socket.
2 Place the battery with the
wires inside the battery
compartment.
3 Slide the battery
compartment cover towards
the center of the handset
until it clicks into place.
4 Charge the handset in the
telephone base or charger.
Charge light
remains on
when charging.
enter the handset menu
Press MeNU when the phone is not in use.
Press CID or until the screen displays the desired
feature menu.
Press
SeLeCT to enter that menu.
To return to the previous menu, press CaNCeL.
To return to idle mode, press and hold CaNCeL.
1.
2.
3.
•
•
IMPOrTaNT!
Refer to the online Complete user’s manual for a full set of
installation and operation instructions. For manual download or
customer service, visit our website at www.vtechphones.com or
call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com
or call 1 (800) 267-7377.
Copyright © 2012 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
96-007701-060-100
Set date and time
Press MeNU when the handset is not in use.
Scroll to Settings then press SeLeCT.
Scroll to Set date/time then press SeLeCT.
Use the dialing keys ( 0-9) to enter the current month, date and
year. Then press SeLeCT.
Use the dialing keys ( 0-9) to enter the hour and minute. Then
press CID or to select aM or PM.
Press SeLeCT to save.
Set number of rings
You can set the answering system to answer an incoming call
after 2, 3, 4, 5 or 6 rings; or toll saver. If you choose toll saver,
the answering system answers a call after 2 rings when you
have new messages, or after 4 rings when you have no
new messages.
Press MeNU when the handset is not in use.
Scroll to answering sys then press SeLeCT.
Scroll to ans sys setup then press SeLeCT.
Scroll to # of rings then press SeLeCT.
Press CID or to choose 6, 5, 4, 3, 2 or Toll saver and
then press SeLeCT to save.
record your own announcement
You can use the preset announcement to answer calls, or replace it
with your own recorded announcement. The announcement can be
up to 90 seconds in length.
Press MeNU when the handset is not in use.
Scroll to answering Sys then press SeLeCT twice.
Press 7 to record.
After the handset announces, “Record after the tone. Press 5
when you are done,” speak towards the handset microphone.
Press
5 when done.
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
IMPOrTaNT:
Check for a dial tone by pressing
. If you hear a dial tone, the
installation is successful.
If you do not hear a dial tone:
Make sure the installation procedures described above are
properly done.
It may be a wiring problem. If you have changed your telephone
service to digital service from a cable company or a VoIP
service provider, the telephone line may need to be rewired to
allow all existing telephone jacks to work. Contact your cable/
VoIP service provider for more information.
•
• Telephone base
Telephone
line cord
Electrical outlet
(not controlled by
a wall switch)
Telephone wall jack
A DSL filter
(not included)
is required if
you have DSL
high-speed
Internet service
Telephone base
power adapter
Charger
Charger
adapter