VTech FS6224_-2-21-3 Quick start - Manual

Quick start guide
FS6220-2/FS6220-3/FS6224/
FS6224-2/FS6224-21/FS6224-3
Introduction
This quick start guide provides you with the basic installation
and setup instructions. A limited set of features are
described in abbreviated form.
You may refer to the Abridged user’s manual provided in the
product package for installation and operation instructions,
or see the online Complete user’s manual at
www.vtechphones.com for complete installation and
operation instructions.
Telephone base and charger installation
Install the telephone base and charger as shown below.
Plug the battery connector
securely into the socket.
1. Place the battery with the
label THIS SIDE UP facing
up and the wires inside the
battery compartment.
2.
Slide the battery
compartment cover towards
the center of the handset
until it clicks into place.
3. Place the handset in the
telephone base or charger
to charge.
4.
Enter the handset menu
Press MENU.
Press or until the screen
displays the desired feature menu.
Press
SELECT.
To return to the previous menu,
press CANCEL.
To return to idle mode,
press and hold CANCEL.
1.
2.
3.
•
•
Set date and time
Press MENU.
Scroll to Settings then press SELECT.
Scroll to Set date/time, then press SELECT.
Use the dialing keys ( 0-9) to enter the month, date and year
and then press SELECT.
Use the dialing keys ( 0-9) to enter the hour and minute.
Press or to select AM or PM.
Press SELECT.
Set number of rings
You can set the answering system to answer an incoming call
after two, three, four, five or six rings; or toll saver. With toll
saver selected, the answering system answers after two rings
when you have new messages, or after four rings when you
have no new messages.
Press MENU.
Scroll to Answering sys, then press SELECT.
Scroll to Ans sys setup, then press SELECT.
Scroll to # of rings, then press SELECT.
Press or to choose 6, 5, 4, 3, 2 or Toll saver,
then press SELECT.
Record your own announcement
You can use the preset announcement to answer calls,
or replace it with your own recorded announcement. The
announcement can be up to 90 seconds in length.
Press MENU.
Scroll to Answering sys, then press SELECT twice.
Press 7 to record.
Speak towards the microphone after the handset announces,
“ Record after the tone. Press 5 when you are done.”
Press 5 when finished.
IMPORTANT!
Refer to the online Complete user’s manual for a full set of
installation and operation instructions. For manual download or
customer service, visit our website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call
1 (800) 267-7377.
Copyright © 2012 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
96-008452-030-100
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
Battery installation and charging
Install the battery as shown below. Once you have installed the
battery, you may be able to make and receive short calls. For best
performance, charge the handset battery continuously for at least
12 hours.
Telephone
wall jack
Telephone
line cord
Electrical
outlet (not
controlled
by a wall
switch)
Telephone
base power
adapter
Charger
adapter
Telephone base Charger
Use only the power adapter(s) and battery(ies) supplied
with this product.
A DSL filter
(not included) is
required if you
have DSL
high-speed
Internet service.
The DSL
filter must be
plugged into
the telephone
wall jack.
Press to
scroll down
Press to
scroll up