Altronix HubWay EXP UTP Power Injector Installation Instructions - Manual (Page 3)

HubWayEXP UTP Power Injector - 3 -
HubWayDv Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 1b, 1d, pg. 3).
10. Measure the output voltage at each Video Balun/Combiner (Figs. 1b, 1d, pg. 3) before making connections to
each camera to insure proper operation and avoid possible damage.
11. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 6, pg. 7).
12. Connect power outputs of HubWayAv or HubWayDv Video Balun/Combiners to power inputs
of cameras (Figs. 1a-1d, pg. 3). Polarity must be observed.
• HubWayAv - Terminals marked [AC POWER] (Figs. 1a, 1b, pg. 3).
• HubWayDv - Terminals marked [– 12VDC +] (Figs. 1c, 1d, pg. 3).
13. Connect the terminals marked [+ DATA -- ] of HubWayAv or HubWayDv Video Balun/Combiners
to data input terminals of cameras for PTZ control (Figs. 1b-1d, pg. 3). Polarity must be observed.
When using fixed cameras disregard this step.
14. Connect the BNC connector of HubWayAv or HubWayDv Video Balun/Combiners to the
BNC video outputs of cameras (Figs. 1b-1d, pg. 3).
15. Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET (ON) position
(Fig. 6, pg. 7).
16. The power LEDs located on the front of the HubWayEXP will illuminate when AC power is present (Fig. 3b, pg. 4).
Note: If any of these LEDs are not illuminated either a voltage output selector switch is in the OFF position or the
PTC is tripped for that channel.
To reset the PTC:
1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain
in the OFF position for approximately 2 minutes in order for the PTC to reset.
2. Eliminate the trouble condition (short circuit or overload).
3. Set the voltage output selector switch for 24VAC or 28VAC (Fig. 3c, pg. 4).
1 - White/Orange [VIDEO +]
2 - Orange [VIDEO -- ]
3 - White/Green [DATA +]
4 - Blue [AC 1]
5 - White/Blue [AC 2]
6 - Green [DATA -- ]
7 - White/Brown [AC 2]
8 - Brown [AC 1]
Fig. 2 - CAT5 Wiring Color Codes
VIDEO BALUN/COMBINER
CAT5 + DATA-- POWER
AC
VIDEO
HubWayAv
VIDEO
AC Power
to Camera
Data to
Camera
--
+ Data to
Camera
Green Power LED
12VDC Power
to Camera
+
--
Red Power LED
Wire
Connectors RJ45 Jack RJ45 Jack
To BNC
Connector
of Camera
To BNC
Connector
of Camera
Structured
Cable from
HubWayEXP
Structured
Cable from
HubWayEXP
VIDEO BALUN/COMBINER
HubWayDv
CAT5 + DATA-- -- 12VDC+
--
+
Wire
Connectors
Fig. 1 - HubWayAv and HubWayDv Video Balun/Combiners
Fig. 1c Fig. 1a
Fig. 1b Fig. 1d
HubWayAv passes AC voltage through pins 4, 5, 7, 8 and
[AC Power] terminals.
HubWayDv converts AC voltage to DC voltage through
pins 4, 5, 7, 8 and [-- 12VDC +] terminals.