Velleman DVM1400 - Manual (Page 8)

28.06.20
Automat
This
move
7.1 Vo
• Conn
• Set t
meas
• Conn
• The
• Whe
• Press
(freq
Notes:
• F
i
• W
“
7.2 Cu
• For
black
• For
lead
• Set t
10A
• Set t
• Whe
appr
• Selec
curre
• Conn
• Read
• Whe
• Press
(freq
Notes:
• F
t
• T
r
• W
b
010
tic battery savi
function switc
e the rotary sw
oltage meas
Do not mea
occur.
Always be ca
fingers behin
terminals wh
nect the black t
the rotary sele
surements
nect the test le
measured valu
n desired, sele
s the Hz/DUT
quency range 4
For DC-measur
ndicated value
When the meas
“OL”. Select a h
urrent meas
Do not measu
Current measu
10A jack. Whe
followed by a
Always be car
fingers behind
measuremen
k lead to the "C
measuremen
to the "COM"
the rotary sele
jack is not fus
the rotary sele
n the range is
ropriate range.
ct the AC or DC
ent).
nect the test pr
d the measured
n desired, sele
s the Hz/DUT
quency range 4
For DC-current
the indicated va
The 400mA-ran
range is not pr
When measurin
break between
ing mode:
hes the meter
witch to reactiv
surements
sure circuits
areful when wo
nd the probe ba
hen the meter i
test lead to the
ctor to
V an
or DC measure
eads to the circ
ue appears on t
ect a range ma
TY button to se
40Hz~400Hz).
rements: when
e is preceded by
sured value is
higher range.
surements
ure current in c
urements: 400
en measuring c
10 minutes br
reful when wor
d the probe bar
ts up to 400m
COM" jack.
ts up to 10A:
jack.
ctor to 10A
se protected.
ctor to 400mA
unknown, alwa
C range with th
robes in series
d value from th
ect a range ma
TY button to se
40Hz~400Hz).
measurement
alue is precede
nge is protecte
rotected.
ng up to 10A, m
2 measureme
DVM14
8
to battery sav
vate the meter
in a CATIV en
orking with volt
arriers at all tim
is linked to a c
e COM jack an
nd press the FU
ements .
cuit under test.
the display.
nually with the
ee the frequenc
Press again to
n a negative po
y a “-” sign.
higher than th
circuits with vo
0mA jack max.
currents up to
eak between 2
king with volta
rriers at all tim
mA: connect th
: connect the r
for measurem
A for measu
ays select the
he FUNC. butt
with the circu
he display.
nually with the
ee the frequenc
Press again to
ts, when a neg
ed by a “-” sign
ed against over
max. 15s conti
nts.
00
ving mode after
.
nvironment o
tages above 60
mes during me
ircuit which is
nd the red test
UNC. button to
.
e RANGE butto
cy or duty cycle
o return to volta
olarity is presen
e selected rang
ltages > 600V
400mA; for m
10A, max. 15s
2 measurement
ages above 60V
mes during mea
he red test lead
ed test lead to
ments up to 10A
rements up to
highest possib
ton ( = alter
it.
e RANGE butto
cy or duty cycle
o return to volta
ative polarity i
n.
r-current with a
nuous measur
r 15 min. Push
or where volta
0Vdc or 30Vac
easurement. Do
being tested.
lead to the
o choose betwe
on.
e of the measu
age display.
nt at the red te
ge limit, the di
measurements
s continuous m
ts.
Vdc or 30Vac r
asurement.
d to the "mA°C
the "10A" jac
A on the 10A ja
400mA on the
ble range and lo
nating current,
on.
e of the measu
age display.
s present at th
an F500mA 60
rement followed
Rev
©Vellema
any button or
ages > 600V
rms. Keep you
o not touch un
HzVΩ jack.
een AC
ured voltage
est lead, the
splay will show
up to 10A use
measurement
rms. Keep your
C" jack and the
ck and the blac
ack. Warning
e mA°C jack.
ower to the
, = direct
ured voltage
he red test lead
0V fuse; the 1
d by a 10 minu
v. 02
n nv
r
may
ur
used
w
the
r
e
ck
: the
d,
0A-
utes