Rainbow Electronics RF22 - Manual (Page 5)

RF22
Version: 0.1 Date: 12/23/2008
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: [email protected] http://www.hoperf.com 5
Table7. GPIO Specifications (GPIO_0, GPIO_1, and GPIO_2)
Parameter Symbol Conditions Min Typ Max Units
Rise Time T
RISE
0.1 x V
DD
to 0.9 x V
DD
, C
L
= 10 pF, DRV<1:0>=HH — — 8 ns
Fall Time T
FALL
0.9 x V
DD
to 0.1 x V
DD
, C
L
= 10 pF, DRV<1:0>=HH — — 8 ns
Input Capacitance C
IN
— — 1 pF
Logic High Level Input Voltage V
IH
V
DD
– 0.6 — V
Logic Low Level Input Voltage V
IL
— — 0.6 V
Input Current I
IN
0<V
IN
< V
DD
–100 — 100 nA
Input Current If Pullup is Activated I
INP
V
IL
=0 V 5 — 25 μA
I
OmaxLL
DRV<1:0>=LL 0.1 0.5 0.8 mA
I
OmaxLH
DRV<1:0>=LH 0.9 2.3 3.5 mA
I
OmaxHL
DRV<1:0>=HL 1.5 3.1 4.8 mA
Maximum Output Current
I
OmaxHH
DRV<1:0>=HH 1.8 3.6 5.4 mA
Logic High Level Output Voltage V
OH
I
OH
< I
Omax
source, V
DD
=1.8 V V
DD
– 0.6 — — V
Logic Low Level Output Voltage V
OL
I
OL
< I
Omax
sink, V
DD
=1.8 V — — 0.6 V
Note: All specification guaranteed by production test unless otherwise noted.
Table8. Absolute Maximum Ratings
Parameter Value Units
V
DD
to GND –0.3, +3.6 V
V
DD
to GND on TX Output Pin –0.3, +8.0 V
Voltage on Digital Control Inputs –0.3, V
DD
+ 0.3 V
Voltage on Analog Inputs –0.3, V
DD
+ 0.3 V
RX Input Power +10 dBm
Operating Ambient Temperature Range T
A
–40 to +85 °C
Thermal Impedance Θ
JA
30 °C/W
Junction Temperature T
J
+125 °C
Storage Temperature Range T
STG
–55 to +125 °C
Note:
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
These are stress ratings only and functional operation of the device at or beyond these ratings in the operational sections of the specifications is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Caution: ESD sensitive device.
Power Amplifier may be damaged if switched on without proper load connected.
1.1. Definition of Test Conditions
Production Test Conditions:
T
A
= +25 o C
V
DD
= +3.3 VDC
External reference signal (XIN) = 1.0 V
PP
at 30 MHz, centered around 0.8 VDC
Production test schematic (unless noted otherwise)
All RF input and output levels referred to the pins of the RF22 (not the RF module)
Extreme Test Conditions:
T
A
= –40 to +85 o C
V
DD
= +1.8 to +3.6 VDC
External reference signal (XIN) = 0.7 to 1.6 V
PP
at 30 MHz centered around 0.8 VDC
Production test schematic (unless noted otherwise)
All RF input and output levels referred to the pins of the RF22 (not the RF module)