Rainbow Electronics MAX5550 - Manual (Page 15)

MAX5550
Dual, 10-Bit, Programmable, 30mA
High-Output-Current DAC
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15
© 2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc.
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
12x16L QFN THIN.EPS
0.10 C 0.08 C
0.10 M C A B
D
D/2
E/2
E
A1
A2
A
E2
E2/2 L
k
e
(ND - 1) X e
(NE - 1) X e
D2
D2/2
b
L
e
L C
L
e
CL
L C
L C
PACKAGE OUTLINE
21-0136 2
1
F
12, 16L THIN QFN, 3x3x0.8mm
MARKING
AAAA
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
EXPOSED PAD VARIATIONS
1.10 T1633-1 0.95
CODES
PKG.
T1233-1
MIN.
0.95
NOM.
1.10
D2
1.25 1.10 0.95 1.25
NOM.
1.10
MAX.
1.25
MIN.
0.95
MAX.
1.25
E2
12 N
k
A2
0.25
NE
A1
ND
0
0.20 REF
- -
3
0.02
3
0.05
L
e
E
0.45
2.90
b
D
A
0.20
2.90
0.70
0.50 BSC.
0.55
3.00
0.65
3.10
0.25
3.00
0.75
0.30
3.10
0.80
16
0.20 REF
0.25 -
0
4
0.02
4
-
0.05
0.50 BSC.
0.30
2.90
0.40
3.00
0.20
2.90
0.70
0.25
3.00
0.75
3.10
0.50
0.80
3.10
0.30
PKG
REF. MIN.
12L 3x3
NOM. MAX. NOM.
16L 3x3
MIN. MAX.
0.35 x 45°
PIN ID JEDEC
WEED-1
0.35 x 45° WEED-2
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO
JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED
WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE.
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.20 mm AND 0.25 mm
FROM TERMINAL TIP.
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220 REVISION C.
NOTES:
T1233-3 1.10 1.25 0.95 1.10 0.35 x 45° 1.25 WEED-1 0.95
T1633F-3 0.65
T1633-4 0.95
0.80 0.95 0.65 0.80
1.10 1.25 0.95 1.10
0.225 x 45° 0.95 WEED-2
0.35 x 45° 1.25 WEED-2
T1633-2 0.95 1.10 1.25 0.95 1.10 0.35 x 45° 1.25 WEED-2
NO
DOWN
BONDS
ALLOWED
YES
NO
YES
N/A
NO
PACKAGE OUTLINE
21-0136 2
2
F
12, 16L THIN QFN, 3x3x0.8
YES WEED-1 1.25 1.10 0.95 0.35 x 45° 1.25 1.10 0.95 T1233-4
T1633FH-3 0.65 0.80 0.95 0.225 x 45° 0.65 0.80 0.95 WEED-2 N/A
10. MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY
11. NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY
Freed 7/13/05