Rainbow Electronics AT29BV010A - Manual (Page 3)

3
AT29BV010A
0519D–FLASH–05/02
Any attempt to write to the device without the 3-byte command sequence will start the
internal write timers. No data will be written to the device; however, for the duration of
t
WC
, a read operation will effectively be a polling operation.
After the software data protection’s 3-byte command code is given, a byte load is per-
formed by applying a low pulse on the WE or CE input with CE or WE low (respectively)
and OE high. The address is latched on the falling edge of CE or WE, whichever occurs
last. The data is latched by the first rising edge of CE or WE.
The 128 bytes of data must be loaded into each sector. Any byte that is not loaded dur-
ing the programming of its sector will be indeterminate. Once the bytes of a sector are
loaded into the device, they are simultaneously programmed during the internal pro-
gramming period. After the first data byte has been loaded into the device, successive
bytes are entered in the same manner. Each new byte to be programmed must have its
high to low transition on WE (or CE) within 150 µs of the low to high transition of WE (or
CE) of the preceding byte. If a high to low transition is not detected within 150 µs of the
last low to high transition, the load period will end and the internal programming period
will start. A7 to A16 specify the sector address. The sector address must be valid during
each high to low transition of WE (or CE). A0 to A6 specify the byte address within the
sector. The bytes may be loaded in any order; sequential loading is not required.
HARDWARE DATA PROTECTION: Hardware features protect against inadvertent
programs to the AT29BV010A in the following ways: (a) V
CC
sense – if V
CC
is below
2.0V (typical), the program function is inhibited; (b) V
CC
power on delay – once V
CC
has
reached the V
CC
sense level, the device will automatically time out 10 ms (typical)
before programming; (c) Program inhibit – holding any one of OE low, CE high or WE
high inhibits program cycles; and (d) Noise filter – pulses of less than 15 ns (typical) on
the WE or CE inputs will not initiate a program cycle.
INPUT LEVELS: While operating with a 2.7V to 3.6V power supply, the address inputs
and control inputs
(OE, CE and WE) may be driven from 0 to 5.5V without adversely
affecting the operation of the device. The I/O lines can only be driven from 0 to V
CC
+
0.6V.
PRODUCT IDENTIFICATION: The product identification mode identifies the device
and manufacturer as Atmel. It may be accessed by hardware or software operation. The
hardware operation mode can be used by an external programmer to identify the correct
programming algorithm for the Atmel product. In addition, users may wish to use the
software product identification mode to identify the part (i.e., using the device code), and
have the system software use the appropriate sector size for program operations. In this
manner, the user can have a common board design for 256K to 4-megabit densities
and, with each density’s sector size in a memory map, have the system software apply
the appropriate sector size.
For details, see Operating Modes (for hardware operation) or Software Product Identifi-
cation. The manufacturer and device code is the same for both methods of identification.
DATA POLLING: The AT29BV010A features DATA polling to indicate the end of a
program cycle. During a program cycle an attempted read of the last byte loaded will
result in the complement of the loaded data on I/O7. Once the program cycle has been
completed, true data is valid on all outputs and the next cycle may begin. DATA polling
may begin at any time during the program cycle.
TOGGLE BIT: In addition to DATA polling the AT29BV010A provides another method
for determining the end of a program or erase cycle. During a program or erase opera-
tion, successive attempts to read data from the device will result in I/O6 toggling
between one and zero. Once the program cycle has completed, I/O6 will stop toggling