Rainbow Electronics MAX2114 - Manual (Page 5)

MAX2114
DBS Direct Downconverter
_______________________________________________________________________________________ 5
Note 1: Minimum and maximum values are guaranteed by design and characterization over supply voltage.
Note 2 Driving differential load of 10k Ω || 15pF.
Note 3: Two signals are applied to RFIN_ at (f LO - 100MHz) and (f LO - 199MHz). V GC2 = 1V, V GC1 is set so that the baseband out-
puts are at 590mVp-p. IM products are measured at baseband outputs but are referred to RF inputs.
Note 4: Two signals are applied to RFIN_ at 1200MHz and 2150MHz. V GC2 = 1V, V GC1 is set so that the baseband outputs are at
590mVp-p. IM products are measured at baseband outputs but are referred to RF inputs.
Note 5: P RFIN_ = -40dBm so that front-end IM contributions are minimized.
Note 6: Using L64733/L64734 demo board from LSI Logic.
Note 7: Downconverted level, in dBc, of carrier present at f LO
× 2, f
LO = 1180MHz, f VCO = 590MHz, V RFBAND = unconnected.
Note 8: Downconverted level, in dBc, of carrier present at f O / 2, f LO = 2175MHz, f VCO = 1087.5MHz, V RFBAND = 2.4V.
Note 9: Leakage is dominated by board parasitics.
Note 10: V
CPG1
= V
CPG2
= V
RFBAND
= V
INSEL
= 0.5V, f
FLCLK
= 0.5MHz.
Note 11: Guaranteed by design and characterization over supply and temperature.
Note 12: Measured at tuned frequency with PLL locked. PLL loop bandwidth = 3kHz. All phase noise measurements assume tank
components have a Q > 50.
AC ELECTRICAL CHARACTERISTICS (continued)
(IC driven single-ended with RFIN- AC-terminated in 75 Ω to GND, V
CC = +4.75V to +5.25V, V IOUT_ = V QOUT_ = 0.59Vp-p,
C IOUT_ = C QOUT_ = 10pF, f FCLK = 500kHz, R IOUT_ = R QOUT_ = 10k Ω, V
LOBUFSEL = 0.5V, V RFBAND = V INSEL = V CPG1 = V CPG2 = +2.4V,
V PLLIN+ = V MOD+ = +1.3V, V PLLIN- = V MOD- = +1.1V, T A = +25°C, unless otherwise noted. Typical values are at V CC = +5V.)
LOCAL OSCILLATOR
SYNTHESIZER
-96
PARAMETER SYMBOL MIN TYP MAX UNITS
At 100kHz offset, f LO = 2175MHz
dBc/Hz LO Phase Noise (Notes 6, 12) -75 At 10kHz offset, f LO = 2175MHz
58
0 Figure 1
f RFIN = 2175MHz dB RFIN+ to LO Input Isolation (Note 9)
-60
590 1180 MHz LO Tuning Range (Note 11)
ns
4 7.26 MHz Crystal Frequency Range (Note 1)
0.8 1 1.5 Load = 10pF | | 10k Ω, f
XTLOUT = 4MHz Vp-p XTLOUT Output Voltage Swing
At 1kHz offset, f LO = 2175MHz
MOD+, MOD- Hold Time (Note 1) t HM
7 Figure 1
CONDITIONS
ns MOD+, MOD- Setup Time (Note 1) t SUM
70
V LOBUFSEL
≥ 2.4V,
f LO = 925 MHz + 2175MHz
mV RMS LO Buffer Output Voltage (Note 1)
SYNTHESIZER
LOCAL OSCILLATOR