Powersolve Short Form Catalogue - Manual (Page 13)

For full specifications and order information please visit www.deltapowersupplies.com DELTA ELEKTRONIKA
DC POWER SUPPLIES
DELTA ELEKTRONIKA
DC POWER SUPPLIES
22 23
For full specifications and order information please visit www.deltapowersupplies.com
PSC Series
interFaCeS
Specifications
•
Programming and
monitoring resolution: 14 bit
•
Communication speed:
up to 12Mbit/s for PSC-PB
up to 1Mbit/s for PSC-CAN
•
Full scale accuracy: < 0.1%
Functionalities
CANopen Functionalities:
•
SYNC Object
•
Emergency Object
•
Node Guarding
•
Heartbeat
•
Expedited and Nonexpedited SDO transfer
•
Node address range 1 - 127
Features
•
Voltage and current
programming and monitoring
•
Node address setting selectable
•
Read back of power
supply status signals
•
600 V galvanic isolation
•
Factory installed
Interface
PSC-ETH Ethernet Controller
PROFIBUS Functionalities:
•
Slave in a PROFIBUS-DP network
•
DP-V0 standard acc. IEC 61784 Ed.
1:2002 CPF 3/1
•
PROFIBUS protocol acc. IEC 61158
•
Slave address range 1 - 127
PSC Series
interFaCeS
Features
•
Voltage and current
programming and monitoring
•
Up to 15 PSCs on one BUS
•
Software calibration
•
Isolated digital user
in- and outputs
•
Factory installed or
external module
Functionalities
•
Monitoring status outputs: ACF, DCF, CC-
mode, Over Temp, PSOL etc.
•
Two isolated user inputs and outputs
(external modules only)
•
Software calibration for offset and full scale
•
PSC-488 Units can also be configured as
PSC-232
Dimensions and weight:
Dimensions: 89 x 86 x 119 mm
Weight: 0,8 kg
Optional 19” rack mounting
Specifications
•
Programming and
monitoring resolution: 16 bit
•
Linearity error: +/- 2 LSB (prg.)
+/- 1 LSB (mon.)
TC = 10 ppm/°C
•
Input voltage
(external module): 98-264 V AC (48-62 Hz)
External module
PSC-232/488
Standards:
•
Generic Emission: EN 61000-6-3 (EN 55022B)
•
Generic Immunity: EN 61000-6-2
•
Safety: EN 60950 / EN 61010
•
Insulation input / output: 1000 V
rms •
Enclosure: IP20
Features
•
Voltage and current program-
ming and monitoring
•
Uses existing IP-networks
•
Integrated sequencer
•
Software calibration
•
Isolated digital user in- and outputs
•
Factory installed or external module
Specifications
•
Programming and
monitoring resolution: 16 bit
•
Linearity error: +/- 2 LSB (prg.)
+/- 1 LSB (mon.)
TC = 10 ppm/°C
•
Input voltage (external module): 98-264 V AC (48-62 Hz)
Integrated sequencer:
•
Converts power supply into an arbitrary waveform generator
•
Stand-alone automation like a PLC
•
25 free programmable sequences, 2000 steps each
•
Combination of very fast and slow sequences
•
Possibility to create loops, sub-routines, ramps etc. Sequencer
Interface:
•
Monitoring status outputs: ACF, DCF,
CC-mode, Over Temp, PSOL etc.
•
Isolated user inputs (8) and outputs (6)
•
Software calibration for off-
set and full scale
Software Control
& Interfaces
Functionalities
External module PSC-ETH
Standards:
•
Generic Emission EN 61000-6-3 (EN 55022B)
•
Generic Immunity EN 61000-6-2
•
Safety EN 60950 / EN 61010
•
Insulation
in/outputs - case
1000 V
DC •
Enclosure IP20
Dimensions and weight:
Dimensions: 89 x 86 x 119 mm
Weight: 0,7 kg
Optional 19” rack mounting
Interfaces
PSC-CAN CANopen Controller
PSC-PB PROFIBUS Controller
Interfaces
PSC-232 RS232 Controller
PSC-488 IEEE488 Controller