Derale Performance Lighted Black on White 2 1_8" Electric Oil Temperature Gauge Kit - Manual

13009-InstructionSheet Rev-2-2-2011
Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com
INSTALLATION INSTRUCTIONS
TEMPERATURE GAUGE
PART # 13009
WIRING
(See Diagram #4)
1.
Connect an 18 gauge wire to the Temp Sender now mounted on the vehicle.
2. Using a grommet (Not supplied) route the wire through the firewall and into
the passenger compartment where the Temperature Gauge is mounted.
3. Attach the Temp Sender wire to the terminal marked (S) on the gauge.
4. Attach an 18 gauge wire to the terminal marked (-) on the gauge, then attach
the other end of the wire with the black wire coming from the gauge light to a
suitable chassis ground.
5. Attach an 18 gauge wire to the terminal marked (+) on the gauge, then attach
the other end of the wire with the red wire coming from the gauge light to a
12V Switched Ignition source.
Red Gauge Light wire can be connected to dash lights if desired. Note:
Please read these instructions completely before beginning installation
TEMPERATURE SENDER INSTALLATION
OPTION 1 - Pan Installation
Note:
Important:
Note:
OPTION 2 - Vehicle Port Installation
generally
(See Diagram #1)
The Temperature Sender is designed to mount on the oil pan with the included
Temp Sender Pan Adapter Kit. The oil pan must be removed to install this option.
The Temperature Sender can also be used as a drain plug if necessary.
Temperature Sender location should avoid hot exhaust and other
possible obstructions. Be sure there is adequate internal clearance for Jam Nut and
Temp Sender before drilling. We recommend mounting the Temperature Sender on
the side of the pan therefore not compromising ground clearance (See Diagram #1).
1.
Once you have determined the location of the Temp Sender, use a marker to
identify drilling location. (See Diagram #1)
2. Using a center punch, carefully indent the drilling location.
3. Using a drill & 1/2” drill bit, drill hole into the pan. Deburring may be necessary.
4. Install the Temp Sender Pan Adapter onto the pan, making sure the Jam Nut
is on the inside of the pan and the Nylon Washer and the Temp Sender Pan
Adapter is on the outside of the pan (See Diagram #1).
5. Using two 3/4” open end wrenches, tighten securely.
6. Using Teflon Tape or suitable sealant, install Temp Sender into the Temp
Sender Pan Adapter.
Always hold adapter body with a wrench when tightening sender.
(See Diagram #2)
1. Locate a port on the vehicle, found on the vehicles radiator,
manifold or water outlet.
2. Using Teflon Tape or suitable sealant install the Thermostat Switch into the
port on the vehicle.
KIT CONTENTS
QTY. DESCRIPTION
1 Temperature Gauge
1 Gauge mounting Bezel
1 Gauge mounting Bracket
2 10-32 Mounting Nuts & Washers
1 10-32 Temp Sender Nut & Washer
QTY. DESCRIPTION
3 6-32 Mounting Nuts & Washers
1 Temp Sender
1 Jam Nut
1 Nylon Washer
1 Temp Sender Pan Adapter
TOOLS NEEDED
Center Punch
1/2” Drill Bit
Deburring Tool
Teflon Tape
Warning: Installation of accessories should only be undertaken by those with mechanical knowledge and are familiar with working on
vehicles. Always use eye protection (goggles, safety glasses or shield). Park the vehicle in a well lit area, on level ground and apply the
parking brake. Only work on a cold vehicle that has been sitting overnight, failure to do so will result in severe burns and injury. Before starting
the vehicle, make sure no tools or any other items are left under hood that could interfere with or be drawn into moving parts of the engine.
Failure to follow instructions can lead to severe damage and personal injury.
6mm Nut Driver
8mm Nut Driver
12mm Wrench
(2) 3/4” Wrenches
Diagram #1
Jam
Nut
Nylon
Washer
Temp Sender
Pan Adapter
Temp
Sender
OPTION 1 OPTION 2
Temp
Sender
Diagram #3 Gauge Mounting
Bracket
10-32 Mounting Nut & Washer
G ge
Mounting
au
Bezel
Temperature
Gauge
Diagram #2
GAUGE INSTALLATION
1. Identify the best location for mounting the Temperature Gauge.
2. Using the Gauge Mounting Bezel as a template, mark, drill and mount in the
proper location. (See Diagram #3)
3. Install the Temperature Gauge into the Gauge Mounting Bezel. Using the
Gauge Mounting Bracket and 10-32 Mounting Nuts and Washers tighten the
Temperature Gauge into place.
Diagram #4
Back View