Diodes PDS1040CTL - Manual (Page 2)

POWERDI is a registered trademark of Diodes Incorporated.
PDS1040CTL
Document number: DS30485 Rev. 13 - 2
2 of 5
www.diodes.com
February 2014
© Diodes Incorporated
PDS1040CTL
Maximum Ratings
(@T
A
= +25°C, unless otherwise specified.)
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitance load, derate current by 20%.
Characteristic Symbol Value Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage V
RRM
V
RWM
V
R
40 V
RMS Reverse Voltage V
R(RMS)
28 V
Average Rectified Output Current (See also Figure 5) per element
total device
I
O
5
10
A
Non-Repetitive Peak Forward Surge Current, per element
8.3ms Single half sine-wave Superimposed on Rated Load
I
FSM
110 A
Thermal Characteristics
Characteristic Symbol Typ Max Unit
Thermal Resistance Junction to Soldering Point R
θJS
⎯ 2.0 °C/W
Thermal Resistance Junction to Ambient Air (Note 5) R
θJA
95 ⎯ °C/W
Thermal Resistance Junction to Ambient Air (Note 6) R
θJA
75 ⎯ °C/W
Thermal Resistance Junction to Ambient Air (Note 7) R
θJA
50 ⎯ °C/W
Operating and Storage Temperature Range T
J
, T
STG
-65 to +150 °C
Electrical Characteristics
(@T
A
= +25°C, unless otherwise specified.)
Characteristic Symbol Min Typ Max Unit Test Condition
Reverse Breakdown Voltage (Note 8) V
(BR)R
40 ⎯ ⎯ V I
R
= 500µA
Forward Voltage Per Element V
F
⎯ 0.465 0.50
V
I
F
= 5A, T
S
= +25 °C
⎯ 0.41 0.45 I
F
= 5A, T
S
= +100 °C
⎯ 0.39 0.43 I
F
= 5A, T
S
= +125 °C
⎯ 0.55 0.60 I
F
= 10A, T
S
= +25 °C
⎯ 0.53 0.57 I
F
= 10A, T
S
= +100 °C
⎯ 0.52 0.56 I
F
= 10A, T
S
= +125 °C
Reverse Leakage Current (Note 8) Per Element I
R
⎯ 20 200 µA V
R
= 40V, T
S
= +25°C
⎯ 3 25 mA V
R
= 40V, T
S
= +100°C
⎯ 15 150 µA V
R
= 35V, T
S
= +25°C
⎯ 2.5 10 mA V
R
= 35V, T
S
= +100°C
⎯ 6 80 µA V
R
= 17.5V, T
S
= +25°C
⎯ 1 5 mA V
R
= 17.5V, T
S
= +100°C
Notes: 5. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com.
6. Polyimide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com.
7. Polyimide PCB, 2 oz. Copper. Cathode pad dimensions 9.4mm x 7.2mm. Anode pad dimensions 2.7mm x 1.6mm.
8. Short duration pulse test used to minimize self-heating effect.