Diodes PDR5G - Manual

e 3
DS30552 Rev. 6 - 2 1 of 3 PDR5G
PowerDI is a trademark of Diodes Incorporated. www.diodes.com ã Diodes Incorporated
PDR5G
5A GLASS PASSIVATED RECTIFIER
PowerDI ä 5
Features
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Mechanical Data
Characteristic Symbol Value Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
V
RRM
V
RWM
V
R
400 V
RMS Reverse Voltage V
R(RMS) 283 V
Average Rectified Output Current (See also figure 4) I
O 5 A
Non-Repetitive Peak Forward Surge Current
8.3ms Single half sine-wave Superimposed on Rated Load
I
FSM 100 A
Maximum Ratings @ T
A
= 25°C unless otherwise specified
E E1
b1
A
A2
A2
D
b2
b1
e
L1
L1
E
b1
D
b2
b1
e
D2
L
E2
L1
LEFT PIN
RIGHT PIN
Note: Pins Left & Right must
be electrically connected
at the printed circuit board.
BOTTOMSIDE
HEAT SINK
W
Characteristic Symbol Typ Max Unit
Thermal Resistance Junction to Soldering Point R
q JS ¾ 1.5 ° C/W
Thermal Resistance Junction to Ambient Air (Note 2) R
q JA 75 ¾ ° C/W
Thermal Resistance Junction to Ambient Air (Note 3) R
q JA 65 ¾ ° C/W
Thermal Resistance Junction to Ambient Air (Note 4) R
q JA
45 ¾ ° C/W
Operating Temperature Range T
j ¾ -65 to +150 ° C
Storage Temperature Range T
STG ¾ -65 to +150 ° C
Notes: 1. RoHS revision 13.2.2003. Glass and High Temperature Solder Exemptions Applied, see EU Directive Annex Notes 5 and 7.
2. FR-4 PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. T
A
= 25°C
3. Polymide PCB, 2 oz. Copper, minimum recommended pad layout per http://www.diodes.com/datasheets/ap02001.pdf. T A
= 25°C
4. Polymide PCB, 2 oz. Copper. Cathode pad dimensions 9.4 mm x 7.2 mm. Anode pad dimensions 2.7 mm x 1.6 mm. T A
= 25°C
Thermal Characteristics
· Glass Passivated Die Construction
· Low Leakage Current
· Lead Free Finish, RoHS Compliant (Note 1)
· "Green" Molding Compound (No Br, Sb)
· Qualified to AEC-Q101 Standards for High Reliability
· Case: PowerDI ä 5
· Case Material: Molded Plastic, “Green” Molding
Compound. UL Flammability Classification Rating 94V-0
· Moisture Sensitivity: Level 1 per J-STD-020C
· Terminals: Finish – Matte Tin annealed over Copper
leadframe. Solderable per MIL-STD-202, Method 208
· Polarity: See Diagram
· Marking: See Page 3
· Weight: 0.096 grams (approximate)
PowerDI ä 5
Dim Min Max
A 1.05 1.15
A2 0.33 0.43
b1 0.80 0.99
b2 1.70 1.88
D 3.90 4.05
D2 3.05 NOM
E 6.40 6.60
e 1.84 NOM
E1 5.30 5.45
E2 3.55 NOM
L 0.75 0.95
L1 0.50 0.65
W 1.20 1.50
All Dimensions in mm