Xylem IM042 R03 Slide Rail Systems Series A10 & APD - Manual (Page 3)

3
SAFETY INSTRUCTIONS
TO AVOID SERIOUS OR FATAL PERSONAL
INJURY OR MAJOR PROPERTY DAMAGE, READ
AND FOLLOW ALL SAFETY INSTRUCTIONS IN
MANUAL AND ON PUMP.
THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT
AND MUST BE KEPT WITH THE SLIDE RAIL.
This is a SAFETY ALERT SYMBOL.
When you see this symbol on the pump
or in the manual, look for one of the fol-
lowing signal words and be alert to the
potential for personal injury or property
damage.
Warns of hazards that WILL cause
serious personal injury, death or major
property damage.
Warns of hazards that CAN cause
serious personal injury, death or major
property damage.
Warns of hazards that CAN cause per-
sonal injury or property damage.
NOTICE: INDICATES SPECIAL INSTRUCTIONS
WHICH ARE VERY IMPORTANT AND
MUST BE FOLLOWED.
HAZARDOUS LIQUIDS OR
FLAMMABLE GASES CAN CAUSE
FIRE, BURNS OR DEATH.
THOROUGHLY REVIEW ALL
INSTRUCTIONS AND WARNINGS
PRIOR TO PERFORMING ANY
WORK ON THIS UNIT.
MAINTAIN ALL SAFETY DECALS.
NOTICE: INSPECT UNIT FOR DAMAGE AND
REPORT ALL DAMAGE TO THE
CARRIER OR DEALER IMMEDIATELY.
DESCRIPTIONS AND SPECIFICATIONS
Goulds Pumps A10 slide rail systems provide easy wet
well pump removal, utilize a self-cleaning quick discon-
nect and guide assembly, and eliminate the need to enter
the wet well.
Model Slide Rail Discharge Pump Discharge
A10-12 1¼” NPTM 1¼” F
A10-2015 1½” NPTM 1½” F
A10-20 2” NPTM 2” F
A10-30 and 4” 125# 3” ANSI Flange
A10-40 ANSI Flange 4” ANSI Flange
A10-60 6” 125#
4” ANSI Flange
ANSI Flange
DANGER
WARNING
CAUTION
PIPING
System piping MUST conform to all local and national
plumbing codes and practices.
To maximize the discharge flow, discharge piping should
be at least as large as the pump discharge. Keep the
discharge pipe as short as possible and avoid unnecessary
fittings.
SLIDE RAIL INSTALLATION
FAILURE TO DISCONNECT AND
LOCKOUT ELECTRICAL POWER
BEFORE ATTEMPTING ANY
MAINTENANCE CAN CAUSE
SHOCK, BURNS OR DEATH.
NOTICE: ALL DIMENSIONS ARE IN INCHES. DO
NOT USE DIMENSIONAL DATA FOR
CONSTRUCTION PURPOSES.
Installation of the slide rail system should locate the pump
opposite the influent opening, preventing stagnate areas
where solids can settle.
NOTICE: GUIDE RAILS MUST BE PLUMB TO
FACILITATE PUMP(S) INSTALLATION
OR REMOVAL.
The containment area floor MUST be flat under the slide
rail base and have sufficient loading capacity to support
the entire weight of the assembly, including the slide rail
base, slide rail guide, pump and all assorted piping.
Prior to anchoring the slide rail base to the containment
area floor, ensure adequate clearance for pump(s) instal-
lation or removal AND for access doors.
NOTICE: MATERIAL SELECTION FOR
CONTAINMENT AREA EQUIPMENT
MUST BE COMPATIBLE WITH
ANTICIPATED FLUIDS AND SERVICE.
WARNING
Hazardous voltage
can shock, burn or
cause death.
WARNING
Hazardous fluids
can cause fire,
burns or death.
WARNING
Wire rope WILL FAIL if worn-out, overloaded, misused,
damaged, improperly maintained or abused.
Wire rope failure may cause serious injury or death!
Protect yourself and others:
• ALWAYS INSPECT wire rope for, WEAR, DAMAGE or
ABUSE BEFORE USE.
• NEVER USE wire rope that is WORN-OUT, DAMAGED
or ABUSED.
• NEVER OVERLOAD a wire rope.
• INFORM YOURSELF: Read and understand
manufacturer’s literature or “Wire Rope and Wire
Rope Sling Safety Bulletin”.*
• REFER TO APPLICABLE CODES, STANDARDS and
REGULATIONS for INSPECTION REQUIREMENTS and
REMOVAL CRITERIA.*
* For additional information or the BULLETIN, ask your
employer or wire rope supplier.
© 1993, Wire Rope Technical Board Form No. 193