Configuring the boards using internal web pages, Configuring the boards using sis commands, Continued) – Extron Electronics Annotator and USP 507 Output Boards User Manual
Page 2: Commands, or internal web pages, Refer to the sppcp help file for details
Configuring the Boards Using the Front Panel Menu System
To configure the 3G/HD-SDI and DVI-D boards using the front panel menu system, refer
to the relevant device user guide, available at
www.extron.com.
The Annotator and the USP 507 have separate
front panel menus for configuring either the scan
converter board or the DVI-I scaler board.
This menu is accessible only after the board has
been installed
.
Scan Converter Board and Scaler DVI-I Board
Configuration Menus
1.
Press the Menu button repeatedly until either
the relevant Scan Converter Settings menu or
Aux Scaler Configuration menu appears.
2.
Press the Next button to reach each
submenu as desired (see the images at right)
and use the front panel adjustment knobs
([ {) to change the settings.
Configuring the Boards Using the Signal
Processing Products Control Program
1.
Open the Signal Processing Products
Control Program (SPPCP) on the PC that is
connected to the Annotator or USP 507
via a LAN or an RS-232 port.
2.
Connect to the device. A new board relevant
tab (Scan Converter or AUX Scaler)
is now available. Click on the desired tab to
configure the settings.
2
Annotator and USP 507
Optional Output Board • Installation Guide,
(
continued)
There are four ways to configure the boards: via front panel menus, a software program
(SPPCP), Simple Instruction Set (SIS
™
) commands, or internal web pages.
H Size V
2048 2048
Scan Converter
Settings
Rotate to adjust
H value. Rotate
to adjust V value.
Output Format
S-video/Comp
Output Standard
NTSC
Next
Next
Next
Next
Flicker Filter
3
Next
H Center V
2048 2048
Rotate to adjust
H value. Rotate
to adjust V value.
Rotate either to
select output format.
Rotate either to
select output
standard.
H Filter
0
Next
Encoder Filter
0
Next
Rotate either to
adjust encoder filter.
Rotate either to
adjust flicker filter.
Rotate either to
adjust H filter.
Resol 1024x768
Refresh 60.00Hz
Aux Scaler
Configuration
Rotate to adjust
resolution. Rotate
to adjust refresh rate.
Aspect Ratio
Follow
Next
Next
Next
Detail
64
Next
Sync Polarity
H neg V neg
Rotate either to
select aspect
ratio mode.
Test Pattern
Crop
Next
Rotate either to
adjust detail level.
Rotate either to
select test pattern.
Output Type
RGBHV
Next
Rotate either to
select output type.
Rotate either to
adjust sync polarity
values.
NOTE:
3G/HD-SDI and DVI-D output boards are buffered, so resolution and
refresh rates match all other outputs. The output rate must be set to
720p, 1080i, or 1080p to activate the 3G/HD-SDI output.
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West:
+1.714.491.1500
FAX: +1.714.491.1517
Extron USA - East:
+1.919.863.1794
FAX: +1.919.863.1797
© 2012 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners.
www.extron.com
Refer to the SPPCP Help File for details.
Configuring the Boards Using Internal Web Pages
1.
Using a LAN connection, open an Internet browser, enter the IP address of
the unit in the browser address bar, and connect to the unit.
2.
Click on the Configuration tab and configure the settings as needed.
Configuring the Boards Using SIS Commands
The boards can also be configured with specific SIS commands. Refer to the Annotator
or USP 507 User Guide at
.
68-1661-60 Rev C 04 12