Extron Electronics MTPX Plus 6400 Series User Guide - Manual (Page 79)

Command/Response Table for SIS Commands (continued)
Command ASCII Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Audio/RS-232 TP input (wire pair 3 and 6) configuration
NOTE: The RS-232 output insert ports, when enabled ( EX% *1Lrpt } ), override the audio/RS-232 TP input configurations.
Configure input as audio X# *Ø\ Typ X# *Ø ] Define the audio/RS-232 input as audio, such
as provided by an MTP 15HD A transmitter.
Configure input as RS-232 X# *1\ Typ X# *1 ] Define the audio/RS-232 input as serial
communications, such as provided by an
MTP 15HD RS transmitter.
Read TP input configuration X# \ X$] Show the audio/RS-232 wire pair input
definition.
RS-232 output inserts and UART port enable
Enable an RS-232 output
insert port EX% *1Lrpt } Lrpt X% *1 ] Enable the RS-232 insert on the X% output.
This disables the UART port.
Enable a UART port EX@ *2Lrpt } Lrpt X% *2 ] Enable the UART port on the X@ output. This
disables the RS-232 output insert.
Enable the input on the
output (disable both the
RS-232 output insert and
any UART port) EX@ *ØLrpt } Lrpt X% *Ø ] Default condition. Disable the RS-232 insert
and UART port on the
X@ output. The switcher
passes the audio or RS-232 on wire pair 3 and
6 of the tied input.
Enable or disable all ports EX^ *Lrpt } LrptØØ* X@] Enable or disable all RS-232 ports or UARTs
Read the RS-232 output
insert and UART port status EX@ Lrpt } X^] Show the status of the RS-232 output insert
port and the UART port.
Input signal level and peaking and auto calibrating
Set input signal peaking EX# * X& Ipek } Ipek X# * X&] Set a specific pre-peak level for the TP input.
Increment input peaking EX# +Ipek } Ipek X# * X&] Increase the input pre-peaking level by 1.
Decrement input peaking EX# -Ipek } Ipek X# * X&] Decrease the pre-peaking level by 1.
Read input peaking setting EX# Ipek } X&]
Execute auto calibration EX# *ØAADJ }
Aadj X# *2 ] {start}
Qik ] {tie creation}
Aadj X# * X*] {finished}
Ipek X# * X&] {new value}
Tie input X# to output 1 and auto adjust the
peaking on input X# . The X* value in the
response reports whether the adjustment
value was within or outside of the threshold.
Iseq X# * X( * X( * X(] {new value}
NOTES: • Before issuing the auto calibration command:
1. Disconnect the power and RJ-45 cables at the MTP transmitter connected
to
X# .
2. Connect the cables removed in step 1 to the included MTP signal generator.
3. If the input cable is longer than 200 feet (60 m), place the Pre-Peak switch
on the MTP signal generator to on (up when the RJ-45 connector on the
signal generator is to the right as shown at right). If the cable is shorter
than 200 feet (60 m), place the switch down.
• The MTP signal generator does not work on cable lengths over 400 feet
(120 m). Set the level and peaking to its maximum value of 255.
Pre-Peak
is on
NOTE: X@ = Output number 01 – (maximum number of outputs for your matrix size)
X# = TP input number 01 – (maximum number of TP inputs for your matrix size)
X$ = Audio / RS-232 wire pair input type 0 = audio 1 = RS-232
X% = RS-232 output insert port number 01 – 16
X^ = RS-232 output insert status or port 0 = disabled 1 = RS-232 enabled 2 = UART enabled
X& = Input level and peaking range 000 – 255
X* = Threshold 0 = outside of threshold 1 = within threshold
X( = Skew adjustment range 00 – 31 (each step = 2 ns)
MTPX Plus 6400 Series Matrix Switchers • Programming Guide 73